9 material differences · fewer than 12
Tractor oneIMT 5130/51361982–1992No measured PTO figureTractor twoJohn Deere 74101997–2002109.4 hpMeasured at the PTO · OECD Test 1750
Which should you choose?
Read our verdict on the 5130/5136 and the 7410 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
9 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | 5130/5136 | 7410 | Gap |
|---|---|---|---|
| Measured performance | |||
| PTO power, measured measured | — | 109.4 hp | — |
| Drawbar power, measured measured | — | 98.2 hp | — |
| Engine | |||
| Engine power, claimed claimed | 133.2 hp | — | — |
| Engine declared | IMR-PERKINS TS 46/T (T 6.354.4) | John Deere 6.068 TRW-51 | differs |
| Displacement declared | 5.80 L | 6.79 L | +17% 7410 |
| Maximum torque declared | 304 lb·ft · 412 N·m | 361 lb·ft · 490.0 N·m | +19% 7410 |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6–31.1 mph · 30–50 km/h | differs |
| Clutch declared | — | Pedal-operated hydraulic wet John Deere multi-disc clutch | — |
| Hydraulics & hitch | |||
| Hydraulic centre declared | — | Closed centre | — |
| Hydraulic control declared | — | Load sensing | — |
| Pump flow declared | 10.2 gpm · 38.8 L/min | 26.9 gpm · 101.8 L/min | +162% 7410 |
| Pressure declared | — | 2,538 psi · 175 bar | — |
| Rear PTO speeds declared | 540/1000 rpm | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 11,718 lb · 5,315 kg | 11,490–12,738 lb · 5,212–5,778 kg | differs |
| Wheelbase declared | 108.3 in · 2,750 mm | 103.3–111.8 in · 2,625–2,840 mm | — |
| Length declared | 178.0 in · 4,521 mm | 174.6 in · 4,435 mm | — |
| Width declared | 82.7 in · 2,100 mm | 96.0–105.7 in · 2,438–2,686 mm | differs |
| Ground clearance declared | 18.1 in · 460 mm | 14.2–15.7 in · 360–400 mm | differs |
| Turning radius, braked declared | 14.0 ft · 4.28 m | — | — |
| Fuel tank declared | 227.2 qt · 215.0 L | 199.7 qt · 189.0 L | +14% 5130/5136 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
IMT 5130/5136 sources
- Source: Traktorenlexikon, “IMT 5130/5136”
John Deere 7410 sources
- Source: OECD test report 1750, 1998
- Source: Traktorenlexikon, “John Deere 7410”
- Source: OECD test report 1751, 1998