Hürlimann H-6130 A or J.I. Case 1090?
Which should you choose?
On performance, every comparable figure that differs favours the J.I. Case 1090: hydraulic flow. On features, the Hürlimann H-6130 A is ahead on PTO speeds and drive.
- The Hürlimann H-6130 A suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 540 rpm.
- The J.I. Case 1090 suits loader and hydraulic implement work better on this data: 55% (21.6 L/min / 5.7 gpm) more hydraulic flow.
- The Hürlimann H-6130 A suits heavy draft work (ploughing, cultivating) better on this data: 22% (1,035 kg / 2,282 lb) heavier and four-wheel drive.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | H-6130 A | 1090 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 78.6 kW (105.4 hp)Traktorenlexikon, “Hürlimann H 6130” | 77.5 kW (104.0 hp)Traktorenlexikon, “Case 1090” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the H-6130 A and the 1090. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the H-6130 A and the 1090. |
| Which pumps more oil for implements? | 39.0 L/min (10.3 gpm)Traktorenlexikon, “Hürlimann H 6130” | 60.6 L/min (16.0 gpm)Traktorenlexikon, “Case 1090” | AheadThe J.I. Case 1090 has 55% more hydraulic flow (21.6 L/min / 5.7 gpm) than the Hürlimann H-6130 A (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 4,210 kg (9,281 lb)Traktorenlexikon, “Hürlimann H 6130” | — | No figureNo call on three-point lift: no figure on record for the 1090. |
| Which is heavier, for traction? | 5,750 kg (12,677 lb)Traktorenlexikon, “Hürlimann H 6130” | 4,715 kg (10,395 lb)Traktorenlexikon, “Case 1090” | Ahead (a fact, not an advantage)The Hürlimann H-6130 A is 22% heavier (1,035 kg / 2,282 lb) than the J.I. Case 1090 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 8,000 kg (17,637 lb)Traktorenlexikon, “Hürlimann H 6130” | — | No figureNo call on maximum permissible mass: no figure on record for the 1090. |
| Which has the wider choice of gears? | 12 to 24Traktorenlexikon, “Hürlimann H 6130” | 8 to 12Traktorenlexikon, “Case 1090” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the H-6130 A and the 1090. |
| Which is faster on the road? | 25 km/h (15.5 mph)Traktorenlexikon, “Hürlimann H 6130” | 25 km/h (15.5 mph)Traktorenlexikon, “Case 1090” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Hürlimann H 6130” | 1000 rpmTraktorenlexikon, “Case 1090” | AheadThe Hürlimann H-6130 A offers 540 rpm at the PTO, which the J.I. Case 1090 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the H-6130 A and the 1090. |
| Which drives on both axles? | 4WDTraktorenlexikon, “Hürlimann H 6130” | 2WDTraktorenlexikon, “Case 1090” | AheadThe Hürlimann H-6130 A is available with four-wheel drive; the J.I. Case 1090 is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1979–1982 | 1970 | Ahead (a fact, not an advantage)The Hürlimann H-6130 A is newer: production began 9 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The J.I. Case 1090 has 55% more hydraulic flow (21.6 L/min / 5.7 gpm) than the Hürlimann H-6130 A (both pump flow, as stated by the source).
- The Hürlimann H-6130 A is 22% heavier (1,035 kg / 2,282 lb) than the J.I. Case 1090 (both unladen weight, as stated by the source).
- The Hürlimann H-6130 A offers 540 rpm at the PTO, which the J.I. Case 1090 does not (as stated by the sources).
- The Hürlimann H-6130 A is available with four-wheel drive; the J.I. Case 1090 is two-wheel drive (as stated by the sources).
- The Hürlimann H-6130 A is newer: production began 9 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources