Hürlimann H-478 "Prestige" or VALMET 900?
Which should you choose?
On performance, every comparable figure that differs favours the VALMET 900: hydraulic flow. On features, the Hürlimann H-478 "Prestige" is ahead on PTO speeds.
- The Hürlimann H-478 "Prestige" suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 1000 rpm.
- The VALMET 900 suits loader and hydraulic implement work better on this data: 38% (15.2 L/min / 4.0 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | H-478 "Prestige" | 900 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 54.3 kW (72.8 hp)Traktorenlexikon, “Hürlimann H 478 Prestige” | 54.0 kW (72.4 hp)Traktorenlexikon, “Valmet 900/II” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the H-478 "Prestige" and the 900. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the H-478 "Prestige" and the 900. |
| Which pumps more oil for implements? | 40.5 L/min (10.7 gpm)Traktorenlexikon, “Hürlimann H 478 Prestige” | 55.7 L/min (14.7 gpm)Traktorenlexikon, “Valmet 900/II” | AheadThe VALMET 900 has 38% more hydraulic flow (15.2 L/min / 4.0 gpm) than the Hürlimann H-478 "Prestige" (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,705 kg (5,964 lb)Traktorenlexikon, “Hürlimann H 478 Prestige” | 3,365 kg (7,419 lb)Traktorenlexikon, “Valmet 900/II” | Not comparableNot comparable on three-point lift: the H-478 "Prestige": lift through the full range at the hitch ends, as stated by the source (Traktorenlexikon, “Hürlimann H 478 Prestige”); the 900: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Valmet 900/II”) — not the same quantity, basis and condition. |
| Which is heavier, for traction? | 3,395 kg (7,485 lb)Traktorenlexikon, “Hürlimann H 478 Prestige” | 3,360 kg (7,408 lb)Traktorenlexikon, “Valmet 900/II” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the H-478 "Prestige" and the 900. |
| Which has the wider choice of gears? | 20Traktorenlexikon, “Hürlimann H 478 Prestige” | 8 to 16Traktorenlexikon, “Valmet 900/II” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the H-478 "Prestige" and the 900. |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Hürlimann H 478 Prestige” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Valmet 900/II” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Hürlimann H 478 Prestige” | 540E/540 rpmTraktorenlexikon, “Valmet 900/II” | AheadThe Hürlimann H-478 "Prestige" offers 1000 rpm at the PTO, which the VALMET 900 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the H-478 "Prestige" and the 900. |
| Which drives on both axles? | 4WDTraktorenlexikon, “Hürlimann H 478 Prestige” | 2WD / 4WDTraktorenlexikon, “Valmet 900/II” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1989–1998 | 1997–2002 | Ahead (a fact, not an advantage)The VALMET 900 is newer: production began 8 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The VALMET 900 has 38% more hydraulic flow (15.2 L/min / 4.0 gpm) than the Hürlimann H-478 "Prestige" (both pump flow, as stated by the source).
- The Hürlimann H-478 "Prestige" offers 1000 rpm at the PTO, which the VALMET 900 does not (as stated by the sources).
- The VALMET 900 is newer: production began 8 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on three-point lift: the H-478 "Prestige": lift through the full range at the hitch ends, as stated by the source (Traktorenlexikon, “Hürlimann H 478 Prestige”); the 900: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Valmet 900/II”) — not the same quantity, basis and condition.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources