Güldner G 40 W or John Deere 920?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the G 40 W has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 920 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The John Deere 920 suits loader and hydraulic implement work better on this data: 13% (3.0 L/min / 0.8 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | G 40 W | 920 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 27.8 kW (37.3 hp)Traktorenlexikon, “Güldner G 40W” | 27.2 kW (36.5 hp)Traktorenlexikon, “John Deere 920” | Not comparableNot comparable on power at the PTO shaft: the G 40 W has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 920 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the G 40 W and the 920. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the G 40 W and the 920. |
| Which pumps more oil for implements? | 23 L/min (6.1 gpm)Traktorenlexikon, “Güldner G 40W” | 26 L/min (6.9 gpm)Traktorenlexikon, “John Deere 920” | AheadThe John Deere 920 has 13% more hydraulic flow (3.0 L/min / 0.8 gpm) than the Güldner G 40 W (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | — | 1,245 kg (2,745 lb)Traktorenlexikon, “John Deere 920” | No figureNo call on three-point lift: no figure on record for the G 40 W. |
| Which is heavier, for traction? | 1,675 kg (3,693 lb)Traktorenlexikon, “Güldner G 40W” | 2,150 kg (4,740 lb)Traktorenlexikon, “John Deere 920” | Ahead (a fact, not an advantage)The John Deere 920 is 28% heavier (475 kg / 1,047 lb) than the Güldner G 40 W (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | 3,200 kg (7,055 lb)Traktorenlexikon, “John Deere 920” | No figureNo call on maximum permissible mass: no figure on record for the G 40 W. |
| Which has the wider choice of gears? | 8Traktorenlexikon, “Güldner G 40W” | 8Traktorenlexikon, “John Deere 920” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | YesTraktorenlexikon, “Güldner G 40W” | — | No figureNo call on a creeper range: not stated for the 920. |
| Which is faster on the road? | 19.4 km/h (12.1 mph)Traktorenlexikon, “Güldner G 40W” | 20 km/h (12.4 mph) to 25 km/h (15.5 mph)Traktorenlexikon, “John Deere 920” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540/1150 rpmTraktorenlexikon, “Güldner G 40W” | 540/1000 rpmTraktorenlexikon, “John Deere 920” | AheadThe John Deere 920 offers 1000 rpm at the PTO, which the Güldner G 40 W does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Güldner G 40W” | independentTraktorenlexikon, “John Deere 920” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 2WDTraktorenlexikon, “Güldner G 40W” | 2WDTraktorenlexikon, “John Deere 920” | EvenEven on drive: all two-wheel drive. |
| Which is newer, and what about parts? | 1965–1969 | 1967–1975 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The John Deere 920 has 13% more hydraulic flow (3.0 L/min / 0.8 gpm) than the Güldner G 40 W (both pump flow, as stated by the source).
- The John Deere 920 is 28% heavier (475 kg / 1,047 lb) than the Güldner G 40 W (both unladen weight, as stated by the source).
- The John Deere 920 offers 1000 rpm at the PTO, which the Güldner G 40 W does not (as stated by the sources).
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO independence: every PTO is independent.
- Even on drive: all two-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the G 40 W has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 920 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources