4 material differences · fewer than 12
Tractor oneFiat 80-88/80-88 DT1989–1993No measured PTO figureTractor twoLandini 8560 L (DT) TL 40 N/M (TL-40 DT/M)1988–2000No measured PTO figure
Which should you choose?
We will not advise between these two machines, because their unladen weight differs by more than 25% (50%); the drive differs (4WD; Two-wheel or four-wheel drive). The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
4 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | 80-88/80-88 DT | 8560 L (DT) TL 40 N/M (TL-40 DT/M) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 78.9 hp | 78.9 hp | — |
| Engine declared | — | Perkins A 4.248 | — |
| Displacement declared | — | 4.07 L | — |
| Maximum torque declared | 197 lb·ft · 267 N·m | 208 lb·ft · 282 N·m | +6% 8560 L (DT) TL 40 N/M (TL-40 DT/M) |
| Transmission | |||
| Top speed declared | 23.6 mph · 38 km/h | 18.6 mph · 30 km/h | +27% 80-88/80-88 DT |
| Clutch declared | — | Dry and air-cooled OMG double clutch | — |
| Hydraulics & hitch | |||
| Pump flow declared | — | 11.2 gpm · 42.3 L/min | — |
| Pressure declared | — | 2,756 psi · 190 bar | — |
| Rear PTO speeds declared | 540 rpm / 1000 rpm | 540 rpm / 1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 7,562 lb · 3,430 kg | 5,027 lb · 2,280 kg | +50% 80-88/80-88 DT |
| Wheelbase declared | — | 81.5 in · 2,070 mm | — |
| Length declared | 144.9 in · 3,680 mm | 140.6 in · 3,570 mm | — |
| Width declared | 86.6 in · 2,200 mm | 61.4–89.4 in · 1,560–2,270 mm | differs |
| Ground clearance declared | 16.9 in · 430 mm | 16.5 in · 420 mm | — |
| Turning radius, braked declared | — | 10.9 ft · 3.33 m | — |
| Fuel tank declared | — | 65.5 qt · 62.0 L | — |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Fiat 80-88/80-88 DT sources
- Source: Traktorenlexikon, “Fiatagri 80-88/80-88 DT”
Landini 8560 L (DT) TL 40 N/M (TL-40 DT/M) sources
- Source: Traktorenlexikon, “Landini R 8560 L (DT)”
- Source: Traktorenlexikon, “Massey Ferguson MF 178”