11 material differences · fewer than 12
Tractor oneFiat 940 (DT)1978–1979No measured PTO figureTractor twoFord 7600 (A)1975–1981No measured PTO figure
Which should you choose?
Read our verdict on the 940 (DT) and the 7600 (A) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
11 material differences · 2 fields identical or within 5%, which is not counted as material
| Field | 940 (DT) | 7600 (A) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 90.8 hp | 90.8 hp | — |
| Engine declared | O.M.-FIAT CO 3/80 | Ford 256 DF | differs |
| Displacement declared | 4.94 L | — | — |
| Transmission | |||
| Top speed declared | 15.5 mph · 25 km/h | 18.6 mph · 30 km/h | +20% 7600 (A) |
| Clutch declared | Dry FEREDO double clutch | Pedal operated dry Borg & Beck single disc clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | 10.0 gpm · 38.0 L/min | 9.6 gpm · 36.4 L/min | — |
| Pressure declared | 2,901 psi · 200 bar | — | — |
| Three-point lift, at the coupling points declared | 8,378 lb · 3,800 kg | 5,952 lb · 2,700 kg | +41% 940 (DT) |
| Rear PTO speeds declared | — | 540/1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 8,708 lb · 3,950 kg | 6,109 lb · 2,771 kg | +43% 940 (DT) |
| Wheelbase declared | 93.3 in · 2,370 mm | 87.5 in · 2,223 mm | +7% 940 (DT) |
| Length declared | 159.4 in · 4,050 mm | 145.2 in · 3,689 mm | +10% 940 (DT) |
| Width declared | 76.2–99.7 in · 1,935–2,532 mm | 80.7–101.7 in · 2,051–2,584 mm | differs |
| Ground clearance declared | 22.4 in · 570 mm | 15.7 in · 400 mm | +43% 940 (DT) |
| Turning radius, braked declared | 12.6 ft · 3.84 m | 10.6 ft · 3.23 m | +19% 940 (DT) |
| Fuel tank declared | 95.1 qt · 90.0 L | 79.8 qt · 75.5 L | +19% 940 (DT) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Fiat 940 (DT) sources
- Source: Traktorenlexikon, “Fiat 940/940 DT”
- Source: Traktorenlexikon, “Someca 940”
Ford 7600 (A) sources
- Source: Traktorenlexikon, “Ford 7600”
- Source: Traktorenlexikon, “Ford 6600”