13 material differences
Tractor oneFiat 55-56 LM (DT)from 1988No measured PTO figureTractor twoJohn Deere 2155 (A)1987–1992No measured PTO figure
Which should you choose?
Read our verdict on the 55-56 LM (DT) and the 2155 (A) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
13 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | 55-56 LM (DT) | 2155 (A) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 54.2 hp | 54.3 hp | — |
| Engine declared | Fiat 8035.06.206 or 307 | John Deere 3.179 DL-017 or DL-001 | differs |
| Displacement declared | 2.71 L | 2.94 L | +8% 2155 (A) |
| Maximum torque declared | 128 lb·ft · 173 N·m | — | — |
| Transmission | |||
| Top speed declared | 15.5–18.6 mph · 25–30 km/h | 18.6 mph · 30 km/h | differs |
| Clutch declared | Dry LuK or Valeo double clutch | Pedal-operated dry Fichtel & Sachs single-disc clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | Closed centre | differs |
| Pump flow declared | 8.7 gpm · 32.8 L/min | 14.0 gpm · 52.9 L/min | +61% 2155 (A) |
| Pressure declared | 3,046 psi · 210 bar | 2,321 psi · 160 bar | +31% 55-56 LM (DT) |
| Three-point lift, at the coupling points declared | 3,847 lb · 1,745 kg | 3,616 lb · 1,640 kg | +6% 55-56 LM (DT) |
| Rear PTO speeds declared | 540 rpm | 540 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 4,718 lb · 2,140 kg | 5,104 lb · 2,315 kg | +8% 2155 (A) |
| Wheelbase declared | 80.8 in · 2,052 mm | 74.4 in · 1,889 mm | +9% 55-56 LM (DT) |
| Length declared | 137.0 in · 3,480 mm | 132.9 in · 3,375 mm | — |
| Width declared | 67.7–87.4 in · 1,720–2,220 mm | 79.3 in · 2,015 mm | differs |
| Ground clearance declared | 17.7 in · 450 mm | 14.4 in · 365 mm | +23% 55-56 LM (DT) |
| Turning radius, braked declared | 10.6 ft · 3.23 m | — | — |
| Fuel tank declared | 63.4 qt · 60.0 L | 70.8 qt · 67.0 L | +12% 2155 (A) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Fiat 55-56 LM (DT) sources
Source
- Source: Traktorenlexikon, “Fiatagri 55-56 LM (DT)”
John Deere 2155 (A) sources
Source
- Source: Traktorenlexikon, “John Deere 2155”