10 material differences · fewer than 12
Tractor oneFiat 480-8 (DT)1981–1982No measured PTO figureTractor twoInternational Harvester 423 (MC Cormick-International)1966–1975No measured PTO figure
Which should you choose?
Read our verdict on the 480-8 (DT) and the 423 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | 480-8 (DT) | 423 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 47.3 hp | 39.4 hp | +20% 480-8 (DT) |
| Engine declared | FIAT-IVECO 8035.02.200 (300) | INTERNATIONAL-HARVESTER D-155 | differs |
| Displacement declared | 2.59 L | 2.54 L | — |
| Maximum torque declared | 112 lb·ft · 152 N·m | 125 lb·ft · 169 N·m | +11% 423 |
| Transmission | |||
| Top speed declared | 15.5 mph · 25 km/h | 12.4 mph · 20 km/h | +25% 480-8 (DT) |
| Hydraulics & hitch | |||
| Pump flow declared | 7.1 gpm · 26.8 L/min | 6.7 gpm · 25.5 L/min | — |
| Pressure declared | 2,843 psi · 196 bar | 3,553 psi · 245 bar | +25% 423 |
| Rear PTO speeds declared | 540 rpm | 540 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 3,990 lb · 1,810 kg | 4,442 lb · 2,015 kg | +11% 423 |
| Wheelbase declared | 76.9 in · 1,953 mm | 75.6 in · 1,920 mm | — |
| Length declared | 114.6 in · 2,910 mm | 133.5 in · 3,390 mm | +16% 423 |
| Width declared | 70.5 in · 1,790 mm | 59.9 in · 1,522 mm | +18% 480-8 (DT) |
| Ground clearance declared | 17.9 in · 455 mm | 14.3 in · 363 mm | +25% 480-8 (DT) |
| Turning radius, braked declared | 9.7 ft · 2.95 m | 10.6 ft · 3.22 m | +9% 423 |
| Fuel tank declared | 57.1 qt · 54.0 L | 63.4 qt · 60.0 L | +11% 423 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Fiat 480-8 (DT) sources
- Source: Traktorenlexikon, “Fiat 480-8/480-8 DT”
- Source: Traktorenlexikon, “Fiat 480/480 DT”
International Harvester 423 (MC Cormick-International) sources
- Source: Traktorenlexikon, “McCormick 423”
- Source: Traktorenlexikon, “McCormick 353”