Fiat 400 (DT) or Hermann Lanz D 634 L?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 400 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the D 634 L has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Hermann Lanz D 634 L suits loader and hydraulic implement work better on this data: 42% (550 kg / 1,213 lb) more three-point lift.
- The Fiat 400 (DT) suits heavy draft work (ploughing, cultivating) better on this data: four-wheel drive.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 400 (DT) | D 634 L | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 25.7 kW (34.5 hp)Traktorenlexikon, “Fiat 400/400 DT” | 25.6 kW (34.3 hp)Traktorenlexikon, “HELA D 634 L (D 635 L)” | Not comparableNot comparable on power at the PTO shaft: the 400 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the D 634 L has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 400 (DT) and the D 634 L. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 400 (DT) and the D 634 L. |
| Which pumps more oil for implements? | 21.8 L/min (5.8 gpm)Traktorenlexikon, “Fiat 400/400 DT” | — | No figureNo call on hydraulic flow: no figure on record for the D 634 L. |
| Which lifts more on the three-point hitch? | 1,300 kg (2,866 lb)Traktorenlexikon, “Fiat 400/400 DT” | 1,850 kg (4,079 lb)Traktorenlexikon, “HELA D 634 L (D 635 L)” | AheadThe Hermann Lanz D 634 L has 42% more lift (550 kg / 1,213 lb) than the Fiat 400 (DT) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 1,701 kg (3,750 lb)Traktorenlexikon, “Fiat 400/400 DT” | 1,780 kg (3,924 lb)Traktorenlexikon, “HELA D 634 L (D 635 L)” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 400 (DT) and the D 634 L. |
| Which has the wider choice of gears? | 8Traktorenlexikon, “Fiat 400/400 DT” | 8 to 10Traktorenlexikon, “HELA D 634 L (D 635 L)” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | YesTraktorenlexikon, “HELA D 634 L (D 635 L)” | No figureNo call on a creeper range: not stated for the 400 (DT). |
| Which is faster on the road? | 25 km/h (15.5 mph)Traktorenlexikon, “Fiat 400/400 DT” | 25 km/h (15.5 mph)Traktorenlexikon, “HELA D 634 L (D 635 L)” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Fiat 400/400 DT” | 545/1050 rpmTraktorenlexikon, “HELA D 634 L (D 635 L)” | No figureNo call on PTO speeds: no standard PTO speed stated for the D 634 L. |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Fiat 400/400 DT” | independentTraktorenlexikon, “HELA D 634 L (D 635 L)” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Fiat 400/400 DT” | 2WDTraktorenlexikon, “HELA D 634 L (D 635 L)” | AheadThe Fiat 400 (DT) is available with four-wheel drive; the Hermann Lanz D 634 L is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1968–1974 | 1977–1980 | Ahead (a fact, not an advantage)The Hermann Lanz D 634 L is newer: production began 9 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Hermann Lanz D 634 L has 42% more lift (550 kg / 1,213 lb) than the Fiat 400 (DT) (both lift at the hitch ends, as stated by the source).
- The Fiat 400 (DT) is available with four-wheel drive; the Hermann Lanz D 634 L is two-wheel drive (as stated by the sources).
- The Hermann Lanz D 634 L is newer: production began 9 years later. We hold no parts-availability data, so there is no call on parts.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO independence: every PTO is independent.
- Not comparable on power at the PTO shaft: the 400 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the D 634 L has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow, maximum permissible mass, a creeper range and PTO speeds.
← Every figure for both machines, side by side, with sources