Fahr D 400 C or Güldner G 45 A (S)?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the D 400 C has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the G 45 A (S) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Güldner G 45 A (S) suits heavy draft work (ploughing, cultivating) better on this data: four-wheel drive.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | D 400 C | G 45 A (S) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 32.9 kW (44.1 hp)Traktorenlexikon, “Fahr D 400 C” | 32.9 kW (44.1 hp)Traktorenlexikon, “Güldner G 45A” | Not comparableNot comparable on power at the PTO shaft: the D 400 C has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the G 45 A (S) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the D 400 C and the G 45 A (S). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the D 400 C and the G 45 A (S). |
| Which pumps more oil for implements? | 18.5 L/min (4.9 gpm)Traktorenlexikon, “Fahr D 400 C” | — | No figureNo call on hydraulic flow: no figure on record for the G 45 A (S). |
| Which lifts more on the three-point hitch? | — | 1,910 kg (4,211 lb)Traktorenlexikon, “Güldner G 45A” | No figureNo call on three-point lift: no figure on record for the D 400 C. |
| Which is heavier, for traction? | 2,570 kg (5,666 lb)Traktorenlexikon, “Fahr D 400 C” | 2,405 kg (5,302 lb)Traktorenlexikon, “Güldner G 45A” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 4,000 kg (8,818 lb)Traktorenlexikon, “Fahr D 400 C” | 4,000 kg (8,818 lb)Traktorenlexikon, “Güldner G 45A” | EvenEven on maximum permissible mass (both maximum permissible mass, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which has the wider choice of gears? | 5 to 6Traktorenlexikon, “Fahr D 400 C” | 8Traktorenlexikon, “Güldner G 45A” | AheadThe Güldner G 45 A (S) has 33% more forward gears (2 gears) than the Fahr D 400 C (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the D 400 C and the G 45 A (S). |
| Which is faster on the road? | 20.8 km/h (12.9 mph) to 30.0 km/h (18.6 mph)Traktorenlexikon, “Fahr D 400 C” | 20 km/h (12.4 mph)Traktorenlexikon, “Güldner G 45A” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 575 rpmTraktorenlexikon, “Fahr D 400 C” | 540/1000 rpmTraktorenlexikon, “Güldner G 45A” | No figureNo call on PTO speeds: no standard PTO speed stated for the D 400 C. |
| Which PTO runs independently of the ground drive? | dependent (stops with the clutch)Traktorenlexikon, “Fahr D 400 C” | independentTraktorenlexikon, “Güldner G 45A” | AheadThe Güldner G 45 A (S) has an independent PTO; the Fahr D 400 C’s is dependent (stops with the clutch). |
| Which drives on both axles? | 2WDTraktorenlexikon, “Fahr D 400 C” | 4WDTraktorenlexikon, “Güldner G 45A” | AheadThe Güldner G 45 A (S) is available with four-wheel drive; the Fahr D 400 C is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1954–1957 | 1965–1969 | Ahead (a fact, not an advantage)The Güldner G 45 A (S) is newer: production began 11 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Güldner G 45 A (S) has 33% more forward gears (2 gears) than the Fahr D 400 C (both forward gears, as stated by the source).
- The Güldner G 45 A (S) has an independent PTO; the Fahr D 400 C’s is dependent (stops with the clutch).
- The Güldner G 45 A (S) is available with four-wheel drive; the Fahr D 400 C is two-wheel drive (as stated by the sources).
- The Güldner G 45 A (S) is newer: production began 11 years later. We hold no parts-availability data, so there is no call on parts.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on maximum permissible mass (both maximum permissible mass, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Not comparable on power at the PTO shaft: the D 400 C has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the G 45 A (S) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow, three-point lift, a creeper range and PTO speeds.
← Every figure for both machines, side by side, with sources