Fahr D 28 UW or International Harvester D-324 Standard?
Which should you choose?
On performance, no comparable figure differs by more than its threshold: on this data the machines are level. On features, the Fahr D 28 UW is ahead on PTO independence.
- The Fahr D 28 UW suits PTO-driven implements (mowers, balers, pumps) better on this data: an independent PTO.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | D 28 UW | D-324 Standard | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 16.9 kW (23 hp)Traktorenlexikon, “Fahr D 28 U” | 16.8 kW (22.6 hp)Traktorenlexikon, “McCormick D-324 Standard” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the D 28 UW and the D-324 Standard. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the D 28 UW and the D-324 Standard. |
| Which pumps more oil for implements? | — | — | No figureNo call on hydraulic flow: no figure on record for the D 28 UW and the D-324 Standard. |
| Which lifts more on the three-point hitch? | — | 600 kg (1,323 lb)Traktorenlexikon, “McCormick D-324 Standard” | No figureNo call on three-point lift: no figure on record for the D 28 UW. |
| Which is heavier, for traction? | 2,150 kg (4,740 lb)Traktorenlexikon, “Fahr D 28 U” | 1,536 kg (3,386 lb)Traktorenlexikon, “McCormick D-324 Standard” | Ahead (a fact, not an advantage)The Fahr D 28 UW is 40% heavier (614 kg / 1,354 lb) than the International Harvester D-324 Standard (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the D 28 UW and the D-324 Standard. |
| Which has the wider choice of gears? | 5Traktorenlexikon, “Fahr D 28 U” | 6 to 8Traktorenlexikon, “McCormick D-324 Standard” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | YesTraktorenlexikon, “McCormick D-324 Standard” | No figureNo call on a creeper range: not stated for the D 28 UW. |
| Which is faster on the road? | 20 km/h (12.4 mph)Traktorenlexikon, “Fahr D 28 U” | 19 km/h (11.8 mph)Traktorenlexikon, “McCormick D-324 Standard” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Fahr D 28 U” | 540 rpmTraktorenlexikon, “McCormick D-324 Standard” | EvenEven on PTO speeds: the same speeds (540 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Fahr D 28 U” | dependent (stops with the clutch)Traktorenlexikon, “McCormick D-324 Standard” | AheadThe Fahr D 28 UW has an independent PTO; the International Harvester D-324 Standard’s is dependent (stops with the clutch). |
| Which drives on both axles? | 2WDTraktorenlexikon, “Fahr D 28 U” | 2WDTraktorenlexikon, “McCormick D-324 Standard” | EvenEven on drive: all two-wheel drive. |
| Which is newer, and what about parts? | 1948–1951 | 1958–1962 | Ahead (a fact, not an advantage)The International Harvester D-324 Standard is newer: production began 10 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Fahr D 28 UW is 40% heavier (614 kg / 1,354 lb) than the International Harvester D-324 Standard (both unladen weight, as stated by the source).
- The Fahr D 28 UW has an independent PTO; the International Harvester D-324 Standard’s is dependent (stops with the clutch).
- The International Harvester D-324 Standard is newer: production began 10 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO speeds: the same speeds (540 rpm).
- Even on drive: all two-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow, three-point lift, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources