9 material differences · fewer than 12
Tractor oneFahr D 1771958–1961No measured PTO figureTractor twoInternational Harvester Farmall 2401958–1961No measured PTO figure
Which should you choose?
Read our verdict on the D 177 and the Farmall 240 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
9 material differences · 2 fields identical or within 5%, which is not counted as material
| Field | D 177 | Farmall 240 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 34 hp | 31.5 hp | +6% D 177 |
| Engine declared | Daimler-Benz OM 636 VI-E | INTERNATIONAL HARVESTER C-123 | differs |
| Displacement declared | 1.77 L | 2.01 L | +14% Farmall 240 |
| Maximum torque declared | 69 lb·ft · 93 N·m | 101 lb·ft · 137 N·m | +47% Farmall 240 |
| Transmission | |||
| Top speed declared | 12.2 mph · 19.6 km/h | 14.3 mph · 23 km/h | +17% Farmall 240 |
| Clutch declared | Pedal operated dry Fichtel & Sachs double clutch | — | — |
| Hydraulics & hitch | |||
| Pump flow declared | — | 6.0 gpm · 22.8 L/min | — |
| Pressure declared | 3,556 psi · 245 bar | — | — |
| Rear PTO speeds declared | — | 539 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 3,638 lb · 1,650 kg | 3,763 lb · 1,707 kg | — |
| Maximum permissible mass declared | 5,732 lb · 2,600 kg | — | — |
| Wheelbase declared | 76.8 in · 1,950 mm | 82.2 in · 2,088 mm | +7% Farmall 240 |
| Length declared | 126.0 in · 3,200 mm | 116.0 in · 2,946 mm | +9% D 177 |
| Width declared | 61.1 in · 1,552 mm | 63.0 in · 1,600 mm | — |
| Ground clearance declared | 15.7 in · 400 mm | 17.0 in · 432 mm | +8% Farmall 240 |
| Turning radius, braked declared | 9.3 ft · 2.83 m | 7.5 ft · 2.28 m | +24% D 177 |
| Fuel tank declared | 46.5 qt · 44 L | 64.8 qt · 61.3 L | +39% Farmall 240 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Fahr D 177 sources
- Source: Traktorenlexikon, “Fahr D 177”
- Source: Traktorenlexikon, “Fahr D 177 S”
International Harvester Farmall 240 sources
- Source: Traktorenlexikon, “Farmall Farmall 240”
- Source: Traktorenlexikon, “McCormick Farmall Super-A 1”
- Source: Traktorenlexikon, “IHC Farmall 240”