Eicher 635 K or Hürlimann Prince 435 DT?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 635 K has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the Prince 435 DT has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Eicher 635K suits loader and hydraulic implement work better on this data: 730% (38.7 L/min / 10.2 gpm) more hydraulic flow.
- The Hürlimann Prince 435 DT suits road haulage better on this data: 18% (4.6 km/h / 2.9 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 635 K | Prince 435 DT | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 26 kW (35 hp)Traktorenlexikon, “Eicher 635 K” | 25.8 kW (34.6 hp)Traktorenlexikon, “Hürlimann Prince 435” | Not comparableNot comparable on power at the PTO shaft: the 635 K has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the Prince 435 DT has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 635 K and the Prince 435 DT. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 635 K and the Prince 435 DT. |
| Which pumps more oil for implements? | 44.0 L/min (11.6 gpm)Traktorenlexikon, “Eicher 635 K” | 5.3 L/min (1.4 gpm)Traktorenlexikon, “Hürlimann Prince 435” | AheadThe Eicher 635K has 730% more hydraulic flow (38.7 L/min / 10.2 gpm) than the Hürlimann Prince 435 DT (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 1,615 kg (3,560 lb)Traktorenlexikon, “Eicher 635 K” | — | No figureNo call on three-point lift: no figure on record for the Prince 435 DT. |
| Which is heavier, for traction? | 1,510 kg (3,329 lb)Traktorenlexikon, “Eicher 635 K” | 1,180 kg (2,601 lb)Traktorenlexikon, “Hürlimann Prince 435” | Ahead (a fact, not an advantage)The Eicher 635K is 28% heavier (330 kg / 728 lb) than the Hürlimann Prince 435 DT (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 635 K and the Prince 435 DT. |
| Which has the wider choice of gears? | 11Traktorenlexikon, “Eicher 635 K” | 12Traktorenlexikon, “Hürlimann Prince 435” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 635 K and the Prince 435 DT. |
| Which is faster on the road? | 25.4 km/h (15.8 mph)Traktorenlexikon, “Eicher 635 K” | 30 km/h (18.6 mph)Traktorenlexikon, “Hürlimann Prince 435” | AheadThe Hürlimann Prince 435 DT has 18% more top speed (4.6 km/h / 2.9 mph) than the Eicher 635K (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Eicher 635 K” | 540/1000 rpmTraktorenlexikon, “Hürlimann Prince 435” | AheadThe Hürlimann Prince 435 DT offers 1000 rpm at the PTO, which the Eicher 635K does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the 635 K and the Prince 435 DT. |
| Which drives on both axles? | 2WDTraktorenlexikon, “Eicher 635 K” | 4WDTraktorenlexikon, “Hürlimann Prince 435” | AheadThe Hürlimann Prince 435 DT is available with four-wheel drive; the Eicher 635K is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1986–1993 | 1995–1999 | Ahead (a fact, not an advantage)The Hürlimann Prince 435 DT is newer: production began 9 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Eicher 635K has 730% more hydraulic flow (38.7 L/min / 10.2 gpm) than the Hürlimann Prince 435 DT (both pump flow, as stated by the source).
- The Eicher 635K is 28% heavier (330 kg / 728 lb) than the Hürlimann Prince 435 DT (both unladen weight, as stated by the source).
- The Hürlimann Prince 435 DT has 18% more top speed (4.6 km/h / 2.9 mph) than the Eicher 635K (both top speed forward, as stated by the source).
- The Hürlimann Prince 435 DT offers 1000 rpm at the PTO, which the Eicher 635K does not (as stated by the sources).
- The Hürlimann Prince 435 DT is available with four-wheel drive; the Eicher 635K is two-wheel drive (as stated by the sources).
- The Hürlimann Prince 435 DT is newer: production began 9 years later. We hold no parts-availability data, so there is no call on parts.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Not comparable on power at the PTO shaft: the 635 K has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the Prince 435 DT has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources