Deutz-Fahr DX 6.05 or Fiat 880-5 (DT)?
Which should you choose?
On performance, every comparable figure that differs favours the Deutz-Fahr DX 6.05: hydraulic flow and three-point lift.
- The Deutz-Fahr DX 6.05 suits loader and hydraulic implement work better on this data: 18% (7.4 L/min / 2.0 gpm) more hydraulic flow and 83% (2,360 kg / 5,203 lb) more three-point lift.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | DX 6.05 | 880-5 (DT) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 60.5 kW (81.1 hp)Traktorenlexikon, “Deutz-Fahr DX 6.05” | 60.4 kW (81.0 hp)Traktorenlexikon, “Fiat 880 DT 5” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the DX 6.05 and the 880-5 (DT). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the DX 6.05 and the 880-5 (DT). |
| Which pumps more oil for implements? | 48.8 L/min (12.9 gpm)Traktorenlexikon, “Deutz-Fahr DX 6.05” | 41.4 L/min (10.9 gpm)Traktorenlexikon, “Fiat 880 DT 5” | AheadThe Deutz-Fahr DX 6.05 has 18% more hydraulic flow (7.4 L/min / 2.0 gpm) than the Fiat 880-5 (DT) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 5,200 kg (11,464 lb)Traktorenlexikon, “Deutz-Fahr DX 6.05” | 2,840 kg (6,261 lb)Traktorenlexikon, “Fiat 880 DT 5” | AheadThe Deutz-Fahr DX 6.05 has 83% more lift (2,360 kg / 5,203 lb) than the Fiat 880-5 (DT) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 4,530 kg (9,987 lb)Traktorenlexikon, “Deutz-Fahr DX 6.05” | 3,700 kg (8,157 lb)Traktorenlexikon, “Fiat 880 DT 5” | Ahead (a fact, not an advantage)The Deutz-Fahr DX 6.05 is 22% heavier (830 kg / 1,830 lb) than the Fiat 880-5 (DT) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 6,800 kg (14,991 lb)Traktorenlexikon, “Deutz-Fahr DX 6.05” | — | No figureNo call on maximum permissible mass: no figure on record for the 880-5 (DT). |
| Which has the wider choice of gears? | 15 to 18Traktorenlexikon, “Deutz-Fahr DX 6.05” | 12 to 16Traktorenlexikon, “Fiat 880 DT 5” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the DX 6.05 and the 880-5 (DT). |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 6.05” | 25 km/h (15.5 mph) to 30 km/h (18.6 mph)Traktorenlexikon, “Fiat 880 DT 5” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 6.05” | 540/1000 rpmTraktorenlexikon, “Fiat 880 DT 5” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr DX 6.05” | independentTraktorenlexikon, “Fiat 880 DT 5” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Fahr DX 6.05” | Two-wheel or four-wheel driveTraktorenlexikon, “Fiat 880 DT 5” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1987–1991 | 1980–1984 | Ahead (a fact, not an advantage)The Deutz-Fahr DX 6.05 is newer: production began 7 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr DX 6.05 has 18% more hydraulic flow (7.4 L/min / 2.0 gpm) than the Fiat 880-5 (DT) (both pump flow, as stated by the source).
- The Deutz-Fahr DX 6.05 has 83% more lift (2,360 kg / 5,203 lb) than the Fiat 880-5 (DT) (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr DX 6.05 is 22% heavier (830 kg / 1,830 lb) than the Fiat 880-5 (DT) (both unladen weight, as stated by the source).
- The Deutz-Fahr DX 6.05 is newer: production began 7 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources