Deutz-Fahr DX 4.10 or SOMECA 780 (TD)?
Which should you choose?
On performance, every comparable figure that differs favours the Deutz-Fahr DX 4.10: hydraulic flow and three-point lift. It is also ahead on top speed.
- The Deutz-Fahr DX 4.10 suits loader and hydraulic implement work better on this data: 52% (13.7 L/min / 3.6 gpm) more hydraulic flow and 13% (450 kg / 992 lb) more three-point lift.
- The Deutz-Fahr DX 4.10 suits road haulage better on this data: 20% (5.0 km/h / 3.1 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | DX 4.10 | 780 (TD) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 48 kW (64 hp)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 47.7 kW (64.0 hp)Traktorenlexikon, “Someca 780” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the DX 4.10 and the 780 (TD). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the DX 4.10 and the 780 (TD). |
| Which pumps more oil for implements? | 40.0 L/min (10.6 gpm)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 26.3 L/min (6.9 gpm)Traktorenlexikon, “Someca 780” | AheadThe Deutz-Fahr DX 4.10 has 52% more hydraulic flow (13.7 L/min / 3.6 gpm) than the SOMECA 780 (TD) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 3,800 kg (8,378 lb)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 3,350 kg (7,385 lb)Traktorenlexikon, “Someca 780” | AheadThe Deutz-Fahr DX 4.10 has 13% more lift (450 kg / 992 lb) than the SOMECA 780 (TD) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 3,920 kg (8,642 lb)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 2,410 kg (5,313 lb)Traktorenlexikon, “Someca 780” | Ahead (a fact, not an advantage)The Deutz-Fahr DX 4.10 is 63% heavier (1,510 kg / 3,329 lb) than the SOMECA 780 (TD) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the DX 4.10 and the 780 (TD). |
| Which has the wider choice of gears? | 15 to 18Traktorenlexikon, “Deutz-Fahr DX 4.10” | 8 to 12Traktorenlexikon, “Someca 780” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the DX 4.10 and the 780 (TD). |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 25 km/h (15.5 mph)Traktorenlexikon, “Someca 780” | AheadThe Deutz-Fahr DX 4.10 has 20% more top speed (5.0 km/h / 3.1 mph) than the SOMECA 780 (TD) (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 4.10” | 540/1000 rpmTraktorenlexikon, “Someca 780” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr DX 4.10” | independentTraktorenlexikon, “Someca 780” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Fahr DX 4.10” | Two-wheel or four-wheel driveTraktorenlexikon, “Someca 780” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1985–1988 | 1975–1983 | Ahead (a fact, not an advantage)The Deutz-Fahr DX 4.10 is newer: production began 10 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr DX 4.10 has 52% more hydraulic flow (13.7 L/min / 3.6 gpm) than the SOMECA 780 (TD) (both pump flow, as stated by the source).
- The Deutz-Fahr DX 4.10 has 13% more lift (450 kg / 992 lb) than the SOMECA 780 (TD) (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr DX 4.10 is 63% heavier (1,510 kg / 3,329 lb) than the SOMECA 780 (TD) (both unladen weight, as stated by the source).
- The Deutz-Fahr DX 4.10 has 20% more top speed (5.0 km/h / 3.1 mph) than the SOMECA 780 (TD) (both top speed forward, as stated by the source).
- The Deutz-Fahr DX 4.10 is newer: production began 10 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources