Deutz-Fahr DX 4.10 or IMR-RAKOVICA R-76 Standard?
Which should you choose?
On performance, every comparable figure that differs favours the Deutz-Fahr DX 4.10: hydraulic flow and three-point lift. It is also ahead on forward gears, PTO speeds and drive.
- The Deutz-Fahr DX 4.10 suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 1000 rpm.
- The Deutz-Fahr DX 4.10 suits loader and hydraulic implement work better on this data: 34% (10.1 L/min / 2.7 gpm) more hydraulic flow and 64% (1,485 kg / 3,274 lb) more three-point lift.
- The Deutz-Fahr DX 4.10 suits heavy draft work (ploughing, cultivating) better on this data: 73% (1,655 kg / 3,649 lb) heavier and four-wheel drive.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | DX 4.10 | R-76 Standard | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 48 kW (64 hp)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 47.9 kW (64.2 hp)Traktorenlexikon, “Rakovica R 76” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the DX 4.10 and the R-76 Standard. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the DX 4.10 and the R-76 Standard. |
| Which pumps more oil for implements? | 40.0 L/min (10.6 gpm)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 29.9 L/min (7.9 gpm)Traktorenlexikon, “Rakovica R 76” | AheadThe Deutz-Fahr DX 4.10 has 34% more hydraulic flow (10.1 L/min / 2.7 gpm) than the IMR-RAKOVICA R-76 Standard (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 3,800 kg (8,378 lb)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 2,315 kg (5,104 lb)Traktorenlexikon, “Rakovica R 76” | AheadThe Deutz-Fahr DX 4.10 has 64% more lift (1,485 kg / 3,274 lb) than the IMR-RAKOVICA R-76 Standard (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 3,920 kg (8,642 lb)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 2,265 kg (4,993 lb)Traktorenlexikon, “Rakovica R 76” | Ahead (a fact, not an advantage)The Deutz-Fahr DX 4.10 is 73% heavier (1,655 kg / 3,649 lb) than the IMR-RAKOVICA R-76 Standard (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the DX 4.10 and the R-76 Standard. |
| Which has the wider choice of gears? | 15 to 18Traktorenlexikon, “Deutz-Fahr DX 4.10” | 6Traktorenlexikon, “Rakovica R 76” | AheadThe Deutz-Fahr DX 4.10 has 150% more forward gears (9 gears) than the IMR-RAKOVICA R-76 Standard (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the DX 4.10 and the R-76 Standard. |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 4.10” | 30 km/h (18.6 mph)Traktorenlexikon, “Rakovica R 76” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 4.10” | 540 rpmTraktorenlexikon, “Rakovica R 76” | AheadThe Deutz-Fahr DX 4.10 offers 1000 rpm at the PTO, which the IMR-RAKOVICA R-76 Standard does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr DX 4.10” | independentTraktorenlexikon, “Rakovica R 76” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Fahr DX 4.10” | 2WDTraktorenlexikon, “Rakovica R 76” | AheadThe Deutz-Fahr DX 4.10 is available with four-wheel drive; the IMR-RAKOVICA R-76 Standard is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1985–1988 | 1979–1989 | Ahead (a fact, not an advantage)The Deutz-Fahr DX 4.10 is newer: production began 6 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr DX 4.10 has 34% more hydraulic flow (10.1 L/min / 2.7 gpm) than the IMR-RAKOVICA R-76 Standard (both pump flow, as stated by the source).
- The Deutz-Fahr DX 4.10 has 64% more lift (1,485 kg / 3,274 lb) than the IMR-RAKOVICA R-76 Standard (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr DX 4.10 is 73% heavier (1,655 kg / 3,649 lb) than the IMR-RAKOVICA R-76 Standard (both unladen weight, as stated by the source).
- The Deutz-Fahr DX 4.10 has 150% more forward gears (9 gears) than the IMR-RAKOVICA R-76 Standard (both forward gears, as stated by the source).
- The Deutz-Fahr DX 4.10 offers 1000 rpm at the PTO, which the IMR-RAKOVICA R-76 Standard does not (as stated by the sources).
- The Deutz-Fahr DX 4.10 is available with four-wheel drive; the IMR-RAKOVICA R-76 Standard is two-wheel drive (as stated by the sources).
- The Deutz-Fahr DX 4.10 is newer: production began 6 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO independence: every PTO is independent.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources