11 material differences · fewer than 12
Tractor oneDeutz-Fahr DX 3.75 A1993–1996No measured PTO figureTractor twoSteyr 9078 (a)1993–1995No measured PTO figure
Which should you choose?
Read our verdict on the DX 3.75 A and the 9078 (a) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
11 material differences · 5 fields identical or within 5%, which is not counted as material
| Field | DX 3.75 A | 9078 (a) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 76.6 hp | 77.0 hp | — |
| Engine declared | KHD F4L 913 | Steyr-MWM WD 401.81 | differs |
| Displacement declared | 4.09 L | 4.16 L | — |
| Maximum torque declared | 183 lb·ft · 248 N·m | 215 lb·ft · 292 N·m | +18% 9078 (a) |
| Transmission | |||
| Top speed declared | 18.6–24.9 mph · 30–40 km/h | 18.6–24.9 mph · 30–40 km/h | — |
| Clutch declared | Independent dry double clutch | Dry Fichtel & Sachs double clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | Open centre | — |
| Pump flow declared | 10.6 gpm · 40.0 L/min | 13.3 gpm · 50.5 L/min | +26% 9078 (a) |
| Pressure declared | 3,481 psi · 240 bar | 2,147 psi · 148 bar | +62% DX 3.75 A |
| Rear PTO speeds declared | 540/1000 rpm | 390/540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 7,077 lb · 3,210 kg | 7,430 lb · 3,370 kg | — |
| Maximum permissible mass declared | 11,023 lb · 5,000 kg | 14,330 lb · 6,500 kg | +30% 9078 (a) |
| Wheelbase declared | 88.6 in · 2,250 mm | 95.3 in · 2,420 mm | +8% 9078 (a) |
| Length declared | 141.7 in · 3,600 mm | 158.5 in · 4,025 mm | +12% 9078 (a) |
| Width declared | 84.2 in · 2,138 mm | 73.7 in · 1,873 mm | +14% DX 3.75 A |
| Ground clearance declared | 16.1 in · 408 mm | — | — |
| Turning radius, braked declared | 12.8 ft · 3.90 m | — | — |
| Fuel tank declared | 91.9 qt · 87 L | 105.7 qt · 100.0 L | +15% 9078 (a) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 3.75 A sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 3.75 A”
- Source: Traktorenlexikon, “Deutz-Fahr DX 3.90”
Steyr 9078 (a) sources
- Source: Traktorenlexikon, “Steyr 9078”