11 material differences · fewer than 12
Tractor oneDeutz-Fahr DX 3.75 A1993–1996No measured PTO figureTractor twoNew Holland T-40302008–2012No measured PTO figure
Which should you choose?
Read our verdict on the DX 3.75 A and the T-4030 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
11 material differences · 5 fields identical or within 5%, which is not counted as material
| Field | DX 3.75 A | T-4030 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 76.6 hp | 77.0 hp | — |
| Engine declared | KHD F4L 913 | IVECO F5 AE 9484 B (Tier-III) | differs |
| Displacement declared | 4.09 L | 3.20 L | +28% DX 3.75 A |
| Maximum torque declared | 183 lb·ft · 248 N·m | 229 lb·ft · 311 N·m | +25% T-4030 |
| Transmission | |||
| Top speed declared | 18.6–24.9 mph · 30–40 km/h | 18.6–24.9 mph · 30–40 km/h | — |
| Clutch declared | Independent dry double clutch | — | — |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Pump flow declared | 10.6 gpm · 40.0 L/min | 13.7 gpm · 52.0 L/min | +30% T-4030 |
| Pressure declared | 3,481 psi · 240 bar | — | — |
| Three-point lift, at the coupling points declared | 7,275 lb · 3,300 kg | 6,393 lb · 2,900 kg | +14% DX 3.75 A |
| Rear PTO speeds declared | 540/1000 rpm | 540 rpm / 1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 7,077 lb · 3,210 kg | 6,779 lb · 3,075 kg | — |
| Maximum permissible mass declared | 11,023 lb · 5,000 kg | 11,574 lb · 5,250 kg | — |
| Wheelbase declared | 88.6 in · 2,250 mm | 82.6 in · 2,098 mm | +7% DX 3.75 A |
| Length declared | 141.7 in · 3,600 mm | 143.2 in · 3,637 mm | — |
| Width declared | 84.2 in · 2,138 mm | 73.5–95.6 in · 1,867–2,428 mm | differs |
| Ground clearance declared | 16.1 in · 408 mm | 15.0 in · 380 mm | +7% DX 3.75 A |
| Turning radius, braked declared | 12.8 ft · 3.90 m | 11.1 ft · 3.37 m | +16% DX 3.75 A |
| Fuel tank declared | 91.9 qt · 87 L | 79.3 qt · 75.0 L | +16% DX 3.75 A |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 3.75 A sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 3.75 A”
- Source: Traktorenlexikon, “Deutz-Fahr DX 3.90”
New Holland T-4030 sources
- Source: Traktorenlexikon, “New Holland T4030”