12 material differences
Tractor oneDeutz-Fahr DX 3.651987–1996No measured PTO figureTractor twoFiat 70-56 LM (DTfrom 1988No measured PTO figure
Which should you choose?
Read our verdict on the DX 3.65 and the 70-56 LM (DT → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
12 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | DX 3.65 | 70-56 LM (DT | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 69.1 hp | 69.1 hp | — |
| Engine declared | KHD F4L 912 | Fiat 8045.06.206 or 307 | differs |
| Displacement declared | 3.77 L | 3.61 L | — |
| Maximum torque declared | 180 lb·ft · 244 N·m | 164 lb·ft · 222 N·m | +10% DX 3.65 |
| Transmission | |||
| Top speed declared | 24.9 mph · 40 km/h | 18.6 mph · 30 km/h | +33% DX 3.65 |
| Clutch declared | independent dry double clutch | — | — |
| Hydraulics & hitch | |||
| Hydraulic centre declared | — | Open centre | — |
| Hydraulic control declared | Constant flow | — | — |
| Pump flow declared | 11.3 gpm · 42.6 L/min | 8.7 gpm · 32.8 L/min | +30% DX 3.65 |
| Pressure declared | 3,481 psi · 240 bar | 3,046 psi · 210 bar | +14% DX 3.65 |
| Three-point lift, at the coupling points declared | 7,275 lb · 3,300 kg | 5,600 lb · 2,540 kg | +30% DX 3.65 |
| Rear PTO speeds declared | 540/1000 rpm | 540 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 7,496 lb · 3,400 kg | 5,357 lb · 2,430 kg | +40% DX 3.65 |
| Maximum permissible mass declared | 11,023 lb · 5,000 kg | — | — |
| Wheelbase declared | 88.6 in · 2,250 mm | 86.7 in · 2,203 mm | — |
| Length declared | 150.4 in · 3,820 mm | 143.3 in · 3,640 mm | — |
| Width declared | 85.9 in · 2,183 mm | 71.7–91.3 in · 1,820–2,320 mm | differs |
| Ground clearance declared | 16.1 in · 408 mm | 19.7 in · 500 mm | +23% 70-56 LM (DT |
| Turning radius, braked declared | 15.1 ft · 4.60 m | 10.7 ft · 3.26 m | +41% DX 3.65 |
| Fuel tank declared | 76.1 qt · 72 L | 63.4 qt · 60.0 L | +20% DX 3.65 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 3.65 sources
Source
- Source: Traktorenlexikon, “Deutz-Fahr DX 3.65”
- Source: Traktorenlexikon, “Deutz D 6006”
Fiat 70-56 LM (DT sources
Source
- Source: Traktorenlexikon, “Fiatagri 70-56 LM (DT)”