Deutz-Fahr DX 3.50 or Eicher Mammut 3354?
Which should you choose?
On performance, every comparable figure that differs favours the Deutz-Fahr DX 3.50: hydraulic flow and three-point lift. It is also ahead on forward gears, top speed and PTO speeds.
- The Deutz-Fahr DX 3.50 suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 1000 rpm.
- The Deutz-Fahr DX 3.50 suits loader and hydraulic implement work better on this data: 100% (19.0 L/min / 5.0 gpm) more hydraulic flow and 33% (600 kg / 1,323 lb) more three-point lift.
- The Deutz-Fahr DX 3.50 suits road haulage better on this data: 25% (6.0 km/h / 3.7 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | DX 3.50 | Mammut 3354 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 40.7 kW (54.6 hp)Traktorenlexikon, “Deutz-Fahr DX 3.50” | 40.5 kW (54 hp)Traktorenlexikon, “Eicher 3354 Mammut 74 A” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the DX 3.50 and the Mammut 3354. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the DX 3.50 and the Mammut 3354. |
| Which pumps more oil for implements? | 38.0 L/min (10.0 gpm)Traktorenlexikon, “Deutz-Fahr DX 3.50” | 19.0 L/min (5.0 gpm)Traktorenlexikon, “Eicher 3354 Mammut 74 A” | AheadThe Deutz-Fahr DX 3.50 has 100% more hydraulic flow (19.0 L/min / 5.0 gpm) than the Eicher Mammut 3354 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,400 kg (5,291 lb)Traktorenlexikon, “Deutz-Fahr DX 3.50” | 1,800 kg (3,968 lb)Traktorenlexikon, “Eicher 3354 Mammut 74 A” | AheadThe Deutz-Fahr DX 3.50 has 33% more lift (600 kg / 1,323 lb) than the Eicher Mammut 3354 (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 2,730 kg (6,019 lb) to 3,120 kg (6,878 lb)Traktorenlexikon, “Deutz-Fahr DX 3.50” | 2,650 kg (5,842 lb)Traktorenlexikon, “Eicher 3354 Mammut 74 A” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 4,600 kg (10,141 lb)Traktorenlexikon, “Deutz-Fahr DX 3.50” | — | No figureNo call on maximum permissible mass: no figure on record for the Mammut 3354. |
| Which has the wider choice of gears? | 16Traktorenlexikon, “Deutz-Fahr DX 3.50” | 8Traktorenlexikon, “Eicher 3354 Mammut 74 A” | AheadThe Deutz-Fahr DX 3.50 has 100% more forward gears (8 gears) than the Eicher Mammut 3354 (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the DX 3.50 and the Mammut 3354. |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 3.50” | 24 km/h (14.9 mph)Traktorenlexikon, “Eicher 3354 Mammut 74 A” | AheadThe Deutz-Fahr DX 3.50 has 25% more top speed (6.0 km/h / 3.7 mph) than the Eicher Mammut 3354 (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 3.50” | 540 rpmTraktorenlexikon, “Eicher 3354 Mammut 74 A” | AheadThe Deutz-Fahr DX 3.50 offers 1000 rpm at the PTO, which the Eicher Mammut 3354 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr DX 3.50” | independentTraktorenlexikon, “Eicher 3354 Mammut 74 A” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Fahr DX 3.50” | 4WDTraktorenlexikon, “Eicher 3354 Mammut 74 A” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1984–1996 | 1974–1978 | Ahead (a fact, not an advantage)The Deutz-Fahr DX 3.50 is newer: production began 10 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr DX 3.50 has 100% more hydraulic flow (19.0 L/min / 5.0 gpm) than the Eicher Mammut 3354 (both pump flow, as stated by the source).
- The Deutz-Fahr DX 3.50 has 33% more lift (600 kg / 1,323 lb) than the Eicher Mammut 3354 (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr DX 3.50 has 100% more forward gears (8 gears) than the Eicher Mammut 3354 (both forward gears, as stated by the source).
- The Deutz-Fahr DX 3.50 has 25% more top speed (6.0 km/h / 3.7 mph) than the Eicher Mammut 3354 (both top speed forward, as stated by the source).
- The Deutz-Fahr DX 3.50 offers 1000 rpm at the PTO, which the Eicher Mammut 3354 does not (as stated by the sources).
- The Deutz-Fahr DX 3.50 is newer: production began 10 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources