Deutz-Fahr DX 3.30 or VALMET 600?
Which should you choose?
On performance, every comparable figure that differs favours the VALMET 600: hydraulic flow and three-point lift. On features, the Deutz-Fahr DX 3.30 is ahead on PTO speeds.
- The Deutz-Fahr DX 3.30 suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 1000 rpm.
- The VALMET 600 suits loader and hydraulic implement work better on this data: 47% (17.7 L/min / 4.7 gpm) more hydraulic flow and 34% (724 kg / 1,596 lb) more three-point lift.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | DX 3.30 | 600 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 35.5 kW (47.5 hp)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 36.0 kW (48.3 hp)Traktorenlexikon, “Valmet 600” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the DX 3.30 and the 600. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the DX 3.30 and the 600. |
| Which pumps more oil for implements? | 38.0 L/min (10.0 gpm)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 55.7 L/min (14.7 gpm)Traktorenlexikon, “Valmet 600” | AheadThe VALMET 600 has 47% more hydraulic flow (17.7 L/min / 4.7 gpm) than the Deutz-Fahr DX 3.30 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,131 kg (4,699 lb)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 2,855 kg (6,294 lb)Traktorenlexikon, “Valmet 600” | AheadThe VALMET 600 has 34% more lift (724 kg / 1,596 lb) than the Deutz-Fahr DX 3.30 (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 2,730 kg (6,019 lb)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 3,130 kg (6,900 lb)Traktorenlexikon, “Valmet 600” | Ahead (a fact, not an advantage)The VALMET 600 is 15% heavier (400 kg / 882 lb) than the Deutz-Fahr DX 3.30 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the DX 3.30 and the 600. |
| Which has the wider choice of gears? | 16 to 24Traktorenlexikon, “Deutz-Fahr DX 3.30” | 8 to 16Traktorenlexikon, “Valmet 600” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the DX 3.30 and the 600. |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Valmet 600” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 3.30” | 540E/540 rpmTraktorenlexikon, “Valmet 600” | AheadThe Deutz-Fahr DX 3.30 offers 1000 rpm at the PTO, which the VALMET 600 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr DX 3.30” | — | No figureNo call on PTO independence: not stated for the 600. |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “Deutz-Fahr DX 3.30” | 4WDTraktorenlexikon, “Valmet 600” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1984–1996 | 1997–2002 | Ahead (a fact, not an advantage)The VALMET 600 is newer: production began 13 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The VALMET 600 has 47% more hydraulic flow (17.7 L/min / 4.7 gpm) than the Deutz-Fahr DX 3.30 (both pump flow, as stated by the source).
- The VALMET 600 has 34% more lift (724 kg / 1,596 lb) than the Deutz-Fahr DX 3.30 (both lift at the hitch ends, as stated by the source).
- The VALMET 600 is 15% heavier (400 kg / 882 lb) than the Deutz-Fahr DX 3.30 (both unladen weight, as stated by the source).
- The Deutz-Fahr DX 3.30 offers 1000 rpm at the PTO, which the VALMET 600 does not (as stated by the sources).
- The VALMET 600 is newer: production began 13 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on drive: every machine is available with four-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources