Deutz-Fahr DX 3.30 or SAME Minitaurus 60?
Which should you choose?
On performance, every comparable figure that differs favours the Deutz-Fahr DX 3.30: hydraulic flow. It is also ahead on PTO speeds.
- The Deutz-Fahr DX 3.30 suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 1000 rpm.
- The Deutz-Fahr DX 3.30 suits loader and hydraulic implement work better on this data: 58% (14.0 L/min / 3.7 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | DX 3.30 | Minitaurus 60 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 35.5 kW (47.5 hp)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 35.4 kW (47.5 hp)Traktorenlexikon, “SAME Minitaurus 60” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the DX 3.30 and the Minitaurus 60. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the DX 3.30 and the Minitaurus 60. |
| Which pumps more oil for implements? | 38.0 L/min (10.0 gpm)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 24.0 L/min (6.3 gpm)Traktorenlexikon, “SAME Minitaurus 60” | AheadThe Deutz-Fahr DX 3.30 has 58% more hydraulic flow (14.0 L/min / 3.7 gpm) than the SAME Minitaurus 60 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,131 kg (4,699 lb)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 2,060 kg (4,542 lb)Traktorenlexikon, “SAME Minitaurus 60” | Not comparableNot comparable on three-point lift: the DX 3.30: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Deutz-Fahr DX 3.30”); the Minitaurus 60: lift through the full range at the hitch ends, as stated by the source (Traktorenlexikon, “SAME Minitaurus 60”) — not the same quantity, basis and condition. |
| Which is heavier, for traction? | 2,730 kg (6,019 lb)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 2,190 kg (4,828 lb)Traktorenlexikon, “SAME Minitaurus 60” | Ahead (a fact, not an advantage)The Deutz-Fahr DX 3.30 is 25% heavier (540 kg / 1,190 lb) than the SAME Minitaurus 60 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the DX 3.30 and the Minitaurus 60. |
| Which has the wider choice of gears? | 16 to 24Traktorenlexikon, “Deutz-Fahr DX 3.30” | 14Traktorenlexikon, “SAME Minitaurus 60” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | YesTraktorenlexikon, “SAME Minitaurus 60” | No figureNo call on a creeper range: not stated for the DX 3.30. |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 25 km/h (15.5 mph) to 30 km/h (18.6 mph)Traktorenlexikon, “SAME Minitaurus 60” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 3.30” | 540 rpmTraktorenlexikon, “SAME Minitaurus 60” | AheadThe Deutz-Fahr DX 3.30 offers 1000 rpm at the PTO, which the SAME Minitaurus 60 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr DX 3.30” | independentTraktorenlexikon, “SAME Minitaurus 60” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “Deutz-Fahr DX 3.30” | Two-wheel or four-wheel driveTraktorenlexikon, “SAME Minitaurus 60” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1984–1996 | 1978–1984 | Ahead (a fact, not an advantage)The Deutz-Fahr DX 3.30 is newer: production began 6 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr DX 3.30 has 58% more hydraulic flow (14.0 L/min / 3.7 gpm) than the SAME Minitaurus 60 (both pump flow, as stated by the source).
- The Deutz-Fahr DX 3.30 is 25% heavier (540 kg / 1,190 lb) than the SAME Minitaurus 60 (both unladen weight, as stated by the source).
- The Deutz-Fahr DX 3.30 offers 1000 rpm at the PTO, which the SAME Minitaurus 60 does not (as stated by the sources).
- The Deutz-Fahr DX 3.30 is newer: production began 6 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on three-point lift: the DX 3.30: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Deutz-Fahr DX 3.30”); the Minitaurus 60: lift through the full range at the hitch ends, as stated by the source (Traktorenlexikon, “SAME Minitaurus 60”) — not the same quantity, basis and condition.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources