Deutz-Fahr DX 3.30 or J.I. Case 1290 (DT)?
Which should you choose?
On performance, every comparable figure that differs favours the Deutz-Fahr DX 3.30: hydraulic flow. It is also ahead on forward gears and PTO speeds.
- The Deutz-Fahr DX 3.30 suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 1000 rpm.
- The Deutz-Fahr DX 3.30 suits loader and hydraulic implement work better on this data: 34% (9.6 L/min / 2.5 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | DX 3.30 | 1290 (DT) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 35.5 kW (47.5 hp)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 35.7 kW (47.8 hp)Traktorenlexikon, “Case 1290” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the DX 3.30 and the 1290 (DT). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the DX 3.30 and the 1290 (DT). |
| Which pumps more oil for implements? | 38.0 L/min (10.0 gpm)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 28.4 L/min (7.5 gpm)Traktorenlexikon, “Case 1290” | AheadThe Deutz-Fahr DX 3.30 has 34% more hydraulic flow (9.6 L/min / 2.5 gpm) than the J.I. Case 1290 (DT) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,131 kg (4,699 lb)Traktorenlexikon, “Deutz-Fahr DX 3.30” | — | No figureNo call on three-point lift: no figure on record for the 1290 (DT). |
| Which is heavier, for traction? | 2,730 kg (6,019 lb)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 2,981 kg (6,572 lb)Traktorenlexikon, “Case 1290” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the DX 3.30 and the 1290 (DT). |
| Which has the wider choice of gears? | 16 to 24Traktorenlexikon, “Deutz-Fahr DX 3.30” | 12Traktorenlexikon, “Case 1290” | AheadThe Deutz-Fahr DX 3.30 has 33% more forward gears (4 gears) than the J.I. Case 1290 (DT) (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the DX 3.30 and the 1290 (DT). |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 3.30” | 30 km/h (18.6 mph)Traktorenlexikon, “Case 1290” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 3.30” | 540 rpmTraktorenlexikon, “Case 1290” | AheadThe Deutz-Fahr DX 3.30 offers 1000 rpm at the PTO, which the J.I. Case 1290 (DT) does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr DX 3.30” | independentTraktorenlexikon, “Case 1290” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “Deutz-Fahr DX 3.30” | Two-wheel or four-wheel driveTraktorenlexikon, “Case 1290” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1984–1996 | 1980–1984 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr DX 3.30 has 34% more hydraulic flow (9.6 L/min / 2.5 gpm) than the J.I. Case 1290 (DT) (both pump flow, as stated by the source).
- The Deutz-Fahr DX 3.30 has 33% more forward gears (4 gears) than the J.I. Case 1290 (DT) (both forward gears, as stated by the source).
- The Deutz-Fahr DX 3.30 offers 1000 rpm at the PTO, which the J.I. Case 1290 (DT) does not (as stated by the sources).
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources