13 material differences
Tractor oneDeutz-Fahr DX 3.101984–1990No measured PTO figureTractor twoSOMECA 470 (TD)1980No measured PTO figure
Which should you choose?
Read our verdict on the DX 3.10 and the 470 (TD) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
13 material differences · 1 fields identical or within 5%, which is not counted as material
| Field | DX 3.10 | 470 (TD) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 46 hp | 45.3 hp | — |
| Engine declared | KHD F3L 912 | FIAT-IVECO 8035.01.320 | differs |
| Displacement declared | 2.83 L | 2.34 L | +21% DX 3.10 |
| Maximum torque declared | 123 lb·ft · 167 N·m | — | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 15.5 mph · 25 km/h | +20% DX 3.10 |
| Clutch declared | Independent dry double clutch | Pedal-operated two-stage dry FEREDO double clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic control declared | Constant flow | — | — |
| Pump flow declared | 9.1 gpm · 34.4 L/min | 5.6 gpm · 21.2 L/min | +62% DX 3.10 |
| Pressure declared | 3,481 psi · 240 bar | 2,843 psi · 196 bar | +22% DX 3.10 |
| Rear PTO speeds declared | 540/1000 rpm | 540 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 5,600 lb · 2,540 kg | 3,120 lb · 1,415 kg | +80% DX 3.10 |
| Maximum permissible mass declared | 8,818 lb · 4,000 kg | — | — |
| Wheelbase declared | 79.2 in · 2,012 mm | 73.4 in · 1,865 mm | +8% DX 3.10 |
| Length declared | 137.4 in · 3,490 mm | 124.0 in · 3,150 mm | +11% DX 3.10 |
| Width declared | 70.4 in · 1,788 mm | 48.0 in · 1,220 mm | +47% DX 3.10 |
| Ground clearance declared | 16.1 in · 410 mm | 14.6 in · 370 mm | +11% DX 3.10 |
| Fuel tank declared | 87.7 qt · 83 L | 57.1 qt · 54.0 L | +54% DX 3.10 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 3.10 sources
Source
- Source: Traktorenlexikon, “Deutz-Fahr DX 3.10”
- Source: Traktorenlexikon, “Deutz D 4006 P”
SOMECA 470 (TD) sources
Source
- Source: Traktorenlexikon, “Someca 470 V”