Deutz-Fahr DX 3.10 or Landini TL 33 N/A (R 5530 F)?
Which should you choose?
On performance, every comparable figure that differs favours the Deutz-Fahr DX 3.10: three-point lift. It is also ahead on drive.
- The Deutz-Fahr DX 3.10 suits loader and hydraulic implement work better on this data: 16% (267 kg / 589 lb) more three-point lift.
- The Deutz-Fahr DX 3.10 suits heavy draft work (ploughing, cultivating) better on this data: 33% (635 kg / 1,400 lb) heavier and four-wheel drive.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | DX 3.10 | TL 33 N/A (R 5530 F) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 32.6 kW (43.7 hp)Traktorenlexikon, “Deutz-Fahr DX 3.10” | 32.4 kW (43.4 hp)Traktorenlexikon, “Landini TL 33 NA” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the DX 3.10 and the TL 33 N/A (R 5530 F). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the DX 3.10 and the TL 33 N/A (R 5530 F). |
| Which pumps more oil for implements? | 34.4 L/min (9.1 gpm)Traktorenlexikon, “Deutz-Fahr DX 3.10” | 37.1 L/min (9.8 gpm)Traktorenlexikon, “Landini TL 33 NA” | EvenEven on hydraulic flow (both pump flow, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which lifts more on the three-point hitch? | 1,900 kg (4,189 lb)Traktorenlexikon, “Deutz-Fahr DX 3.10” | 1,633 kg (3,600 lb)Traktorenlexikon, “Landini TL 33 NA” | AheadThe Deutz-Fahr DX 3.10 has 16% more lift (267 kg / 589 lb) than the Landini TL 33 N/A (R 5530 F) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 2,540 kg (5,600 lb)Traktorenlexikon, “Deutz-Fahr DX 3.10” | 1,905 kg (4,200 lb)Traktorenlexikon, “Landini TL 33 NA” | Ahead (a fact, not an advantage)The Deutz-Fahr DX 3.10 is 33% heavier (635 kg / 1,400 lb) than the Landini TL 33 N/A (R 5530 F) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 4,000 kg (8,818 lb)Traktorenlexikon, “Deutz-Fahr DX 3.10” | — | No figureNo call on maximum permissible mass: no figure on record for the TL 33 N/A (R 5530 F). |
| Which has the wider choice of gears? | 8 to 16Traktorenlexikon, “Deutz-Fahr DX 3.10” | 12 to 20Traktorenlexikon, “Landini TL 33 NA” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the DX 3.10 and the TL 33 N/A (R 5530 F). |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Deutz-Fahr DX 3.10” | 30 km/h (18.6 mph)Traktorenlexikon, “Landini TL 33 NA” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 3.10” | 540/1000 rpmTraktorenlexikon, “Landini TL 33 NA” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the DX 3.10 and the TL 33 N/A (R 5530 F). |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “Deutz-Fahr DX 3.10” | 2WDTraktorenlexikon, “Landini TL 33 NA” | AheadThe Deutz-Fahr DX 3.10 is available with four-wheel drive; the Landini TL 33 N/A (R 5530 F) is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1984–1990 | 1983–1987 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr DX 3.10 has 16% more lift (267 kg / 589 lb) than the Landini TL 33 N/A (R 5530 F) (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr DX 3.10 is 33% heavier (635 kg / 1,400 lb) than the Landini TL 33 N/A (R 5530 F) (both unladen weight, as stated by the source).
- The Deutz-Fahr DX 3.10 is available with four-wheel drive; the Landini TL 33 N/A (R 5530 F) is two-wheel drive (as stated by the sources).
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on hydraulic flow (both pump flow, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources