11 material differences · fewer than 12
Tractor oneDeutz-Fahr DX 3.101984–1990No measured PTO figureTractor twoDeutz-Fahr DX 50 V1978–1985No measured PTO figure
Which should you choose?
We will not advise between these two machines, because their unladen weight differs by more than 25% (62%). The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
11 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | DX 3.10 | DX 50 V | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 46 hp | 45.2 hp | — |
| Engine declared | KHD F3L 912 | KHD F3L 912 | — |
| Displacement declared | 2.83 L | 2.83 L | — |
| Maximum torque declared | 123 lb·ft · 167 N·m | 110 lb·ft · 149 N·m | +12% DX 3.10 |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 13.7 mph · 22 km/h | +36% DX 3.10 |
| Clutch declared | Independent dry double clutch | Independent dry double clutch | — |
| Hydraulics & hitch | |||
| Hydraulic control declared | Constant flow | — | — |
| Pump flow declared | 9.1 gpm · 34.4 L/min | — | — |
| Pressure declared | 3,481 psi · 240 bar | 2,901 psi · 200 bar | +20% DX 3.10 |
| Three-point lift, at the coupling points declared | 4,189 lb · 1,900 kg | 3,924 lb · 1,780 kg | +7% DX 3.10 |
| Rear PTO speeds declared | 540/1000 rpm | 540 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 5,600 lb · 2,540 kg | 3,461 lb · 1,570 kg | +62% DX 3.10 |
| Maximum permissible mass declared | 8,818 lb · 4,000 kg | — | — |
| Wheelbase declared | 79.2 in · 2,012 mm | 70.5 in · 1,790 mm | +12% DX 3.10 |
| Length declared | 137.4 in · 3,490 mm | 126.0 in · 3,200 mm | +9% DX 3.10 |
| Width declared | 70.4 in · 1,788 mm | 43.3 in · 1,100 mm | +63% DX 3.10 |
| Ground clearance declared | 16.1 in · 410 mm | 13.8 in · 350 mm | +17% DX 3.10 |
| Turning radius, braked declared | — | 9.5 ft · 2.89 m | — |
| Fuel tank declared | 87.7 qt · 83 L | 42.3 qt · 40 L | +108% DX 3.10 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 3.10 sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 3.10”
- Source: Traktorenlexikon, “Deutz D 4006 P”
Deutz-Fahr DX 50 V sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 50 V”
- Source: Traktorenlexikon, “Deutz D 4006 P”