10 material differences · fewer than 12
Tractor oneDeutz-Fahr DX 2501982–1983No measured PTO figureTractor twoMassey Ferguson MF 18051975–1977No measured PTO figure
Which should you choose?
We will not advise between these two machines, because they were not built in overlapping years (1982–1983; 1975–1977). The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
10 material differences · 5 fields identical or within 5%, which is not counted as material
| Field | DX 250 | MF 1805 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 217 hp | 207.3 hp | — |
| Engine declared | KHD BF6L 413 FR | Caterpillar 3208-V8 | differs |
| Displacement declared | 9.57 L | 10.42 L | +9% MF 1805 |
| Maximum torque declared | 597 lb·ft · 810 N·m | 485 lb·ft · 657 N·m | +23% DX 250 |
| Transmission | |||
| Top speed declared | 15.5–18.6 mph · 25–30 km/h | 15.5 mph · 25 km/h | differs |
| Clutch declared | — | Pedal-operated dry Borg & Beck single-disc clutch | — |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Pump flow declared | 21.4 gpm · 81 L/min | 25.0 gpm · 94.6 L/min | +17% MF 1805 |
| Three-point lift, at the coupling points declared | 17,968 lb · 8,150 kg | 10,141 lb · 4,600 kg | +77% DX 250 |
| Rear PTO speeds declared | 923 rpm | 1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 20,393 lb · 9,250 kg | 20,944 lb · 9,500 kg | — |
| Maximum permissible mass declared | 26,455 lb · 12,000 kg | 25,353 lb · 11,500 kg | — |
| Wheelbase declared | 118.6 in · 3,012 mm | 120.1 in · 3,050 mm | — |
| Length declared | 213.7 in · 5,427 mm | 244.1 in · 6,200 mm | +14% MF 1805 |
| Width declared | 98.4 in · 2,500 mm | 94.5 in · 2,400 mm | — |
| Ground clearance declared | 20.7 in · 525 mm | 16.9 in · 430 mm | +22% DX 250 |
| Fuel tank declared | 422.7 qt · 400 L | 479.7 qt · 454 L | +14% MF 1805 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 250 sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 250”
- Source: Traktorenlexikon, “Deutz-Fahr DX 230”
Massey Ferguson MF 1805 sources
- Source: Traktorenlexikon, “Massey Ferguson MF 1805”
- Source: Traktorenlexikon, “Massey Ferguson MF 1505”