12 material differences
Tractor oneDeutz-Fahr DX 1101978–1983No measured PTO figureTractor twoJohn Deere 7200 (A)1993–1997No measured PTO figure
Which should you choose?
Read our verdict on the DX 110 and the 7200 (A) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
12 material differences · 2 fields identical or within 5%, which is not counted as material
| Field | DX 110 | 7200 (A) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 101 hp | 100.7 hp | — |
| Engine declared | KHD F6L 912 | John Deere 6.059 TRW-01 or 6.068 TRW-01 | differs |
| Displacement declared | 5.65 L | — | — |
| Maximum torque declared | 257 lb·ft · 349 N·m | 311 lb·ft · 421 N·m | +21% 7200 (A) |
| Transmission | |||
| Top speed declared | 15.5–18.6 mph · 25–30 km/h | 18.6–24.9 mph · 30–40 km/h | differs |
| Clutch declared | Independent dry double clutch | Pedal-operated, hydraulic wet John Deere multi-disc clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Hydraulic control declared | — | Load sensing | — |
| Pump flow declared | 14.7 gpm · 55.7 L/min | 26.2 gpm · 99.2 L/min | +78% 7200 (A) |
| Pressure declared | 3,046–3,771 psi · 210–260 bar | 2,538 psi · 175 bar | differs |
| Rear PTO speeds declared | 540 rpm / 1000 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 9,744 lb · 4,420 kg | 12,679 lb · 5,751 kg | +30% 7200 (A) |
| Maximum permissible mass declared | 14,991 lb · 6,800 kg | 19,842 lb · 9,000 kg | +32% 7200 (A) |
| Wheelbase declared | 105.8 in · 2,688 mm | 112.2 in · 2,850 mm | +6% 7200 (A) |
| Length declared | 176.8 in · 4,490 mm | 174.6 in · 4,435 mm | — |
| Width declared | 90.7 in · 2,304 mm | 96.0–105.7 in · 2,438–2,686 mm | differs |
| Ground clearance declared | 23.2 in · 590 mm | 14.2 in · 360 mm | +64% DX 110 |
| Turning radius, braked declared | 14.0 ft · 4.28 m | — | — |
| Fuel tank declared | — | 215.6 qt · 204.0 L | — |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr DX 110 sources
Source
- Source: Traktorenlexikon, “Deutz-Fahr DX 110”
John Deere 7200 (A) sources
Source
- Source: Traktorenlexikon, “John Deere 7200”