Deutz-Fahr D 6907 A ( C ) or Deutz-Fahr DX 4.10?
Which should you choose?
On performance, every comparable figure that differs favours the Deutz-Fahr DX 4.10: three-point lift.
- The Deutz-Fahr DX 4.10 suits loader and hydraulic implement work better on this data: 58% (1,400 kg / 3,086 lb) more three-point lift.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | D 6907 A ( C ) | DX 4.10 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 48.0 kW (64.4 hp)Traktorenlexikon, “Deutz-Fahr D 6907” | 48 kW (64 hp)Traktorenlexikon, “Deutz-Fahr DX 4.10” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the D 6907 A ( C ) and the DX 4.10. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the D 6907 A ( C ) and the DX 4.10. |
| Which pumps more oil for implements? | — | 40.0 L/min (10.6 gpm)Traktorenlexikon, “Deutz-Fahr DX 4.10” | No figureNo call on hydraulic flow: no figure on record for the D 6907 A ( C ). |
| Which lifts more on the three-point hitch? | 2,400 kg (5,291 lb)Traktorenlexikon, “Deutz-Fahr D 6907” | 3,800 kg (8,378 lb)Traktorenlexikon, “Deutz-Fahr DX 4.10” | AheadThe Deutz-Fahr DX 4.10 has 58% more lift (1,400 kg / 3,086 lb) than the Deutz-Fahr D 6907 A ( C ) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 2,900 kg (6,393 lb)Traktorenlexikon, “Deutz-Fahr D 6907” | 3,920 kg (8,642 lb)Traktorenlexikon, “Deutz-Fahr DX 4.10” | Ahead (a fact, not an advantage)The Deutz-Fahr DX 4.10 is 35% heavier (1,020 kg / 2,249 lb) than the Deutz-Fahr D 6907 A ( C ) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 4,000 kg (8,818 lb)Traktorenlexikon, “Deutz-Fahr D 6907” | — | No figureNo call on maximum permissible mass: no figure on record for the DX 4.10. |
| Which has the wider choice of gears? | 12Traktorenlexikon, “Deutz-Fahr D 6907” | 15 to 18Traktorenlexikon, “Deutz-Fahr DX 4.10” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the D 6907 A ( C ) and the DX 4.10. |
| Which is faster on the road? | 25 km/h (15.5 mph) to 30 km/h (18.6 mph)Traktorenlexikon, “Deutz-Fahr D 6907” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 4.10” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | — | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 4.10” | No figureNo call on PTO speeds: no standard PTO speed stated for the D 6907 A ( C ). |
| Which PTO runs independently of the ground drive? | — | independentTraktorenlexikon, “Deutz-Fahr DX 4.10” | No figureNo call on PTO independence: not stated for the D 6907 A ( C ). |
| Which drives on both axles? | 4WDTraktorenlexikon, “Deutz-Fahr D 6907” | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Fahr DX 4.10” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1983–1984 | 1985–1988 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr DX 4.10 has 58% more lift (1,400 kg / 3,086 lb) than the Deutz-Fahr D 6907 A ( C ) (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr DX 4.10 is 35% heavier (1,020 kg / 2,249 lb) than the Deutz-Fahr D 6907 A ( C ) (both unladen weight, as stated by the source).
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow, maximum permissible mass, a creeper range, PTO speeds and PTO independence.
← Every figure for both machines, side by side, with sources