Deutz-Fahr D 6507 (C) or ZETOR 7011/7045?
Which should you choose?
On performance, every comparable figure that differs favours the Deutz-Fahr D 6507 (C): hydraulic flow. It is also ahead on top speed. On features, the ZETOR 7011/7045 is ahead on PTO speeds.
- The ZETOR 7011/7045 suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 1000 rpm.
- The Deutz-Fahr D 6507 (C) suits loader and hydraulic implement work better on this data: 39% (8.9 L/min / 2.4 gpm) more hydraulic flow.
- The Deutz-Fahr D 6507 (C) suits road haulage better on this data: 20% (5.0 km/h / 3.1 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | D 6507 (C) | 7011/7045 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 41.7 kW (55.9 hp)Traktorenlexikon, “Deutz-Fahr D 6507” | 41.5 kW (55.7 hp)Traktorenlexikon, “Zetor 7011” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the D 6507 (C) and the 7011/7045. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the D 6507 (C) and the 7011/7045. |
| Which pumps more oil for implements? | 31.8 L/min (8.4 gpm)Traktorenlexikon, “Deutz-Fahr D 6507” | 22.9 L/min (6.0 gpm)Traktorenlexikon, “Zetor 7011” | AheadThe Deutz-Fahr D 6507 (C) has 39% more hydraulic flow (8.9 L/min / 2.4 gpm) than the ZETOR 7011/7045 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,400 kg (5,291 lb)Traktorenlexikon, “Deutz-Fahr D 6507” | — | No figureNo call on three-point lift: no figure on record for the 7011/7045. |
| Which is heavier, for traction? | 2,530 kg (5,578 lb)Traktorenlexikon, “Deutz-Fahr D 6507” | 2,930 kg (6,460 lb)Traktorenlexikon, “Zetor 7011” | Ahead (a fact, not an advantage)The ZETOR 7011/7045 is 16% heavier (400 kg / 882 lb) than the Deutz-Fahr D 6507 (C) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 4,000 kg (8,818 lb)Traktorenlexikon, “Deutz-Fahr D 6507” | — | No figureNo call on maximum permissible mass: no figure on record for the 7011/7045. |
| Which has the wider choice of gears? | 8Traktorenlexikon, “Deutz-Fahr D 6507” | 10 to 20Traktorenlexikon, “Zetor 7011” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the D 6507 (C) and the 7011/7045. |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Deutz-Fahr D 6507” | 25 km/h (15.5 mph)Traktorenlexikon, “Zetor 7011” | AheadThe Deutz-Fahr D 6507 (C) has 20% more top speed (5.0 km/h / 3.1 mph) than the ZETOR 7011/7045 (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Deutz-Fahr D 6507” | 540/1000 rpmTraktorenlexikon, “Zetor 7011” | AheadThe ZETOR 7011/7045 offers 1000 rpm at the PTO, which the Deutz-Fahr D 6507 (C) does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | — | independentTraktorenlexikon, “Zetor 7011” | No figureNo call on PTO independence: not stated for the D 6507 (C). |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “Deutz-Fahr D 6507” | 2WD / 4WDTraktorenlexikon, “Zetor 7011” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1982–1984 | 1980–1984 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr D 6507 (C) has 39% more hydraulic flow (8.9 L/min / 2.4 gpm) than the ZETOR 7011/7045 (both pump flow, as stated by the source).
- The ZETOR 7011/7045 is 16% heavier (400 kg / 882 lb) than the Deutz-Fahr D 6507 (C) (both unladen weight, as stated by the source).
- The Deutz-Fahr D 6507 (C) has 20% more top speed (5.0 km/h / 3.1 mph) than the ZETOR 7011/7045 (both top speed forward, as stated by the source).
- The ZETOR 7011/7045 offers 1000 rpm at the PTO, which the Deutz-Fahr D 6507 (C) does not (as stated by the sources).
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources