12 material differences
Tractor oneDeutz-Fahr D 6507 (C)1982–1984No measured PTO figureTractor twoSOMECA 715/5 L (DT)1967–1968No measured PTO figure
Which should you choose?
Read our verdict on the D 6507 (C) and the 715/5 L (DT) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
12 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | D 6507 (C) | 715/5 L (DT) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 62 hp | 62.1 hp | — |
| Engine declared | KHD F4L 912 | O.M.-FIAT CO 3 D/130-70-2 | differs |
| Displacement declared | 3.77 L | — | — |
| Maximum torque declared | 174 lb·ft · 236 N·m | 203 lb·ft · 275 N·m | +17% 715/5 L (DT) |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 15.5 mph · 25 km/h | +20% D 6507 (C) |
| Clutch declared | Independent dry double clutch | Pedal-operated dry two-stage FERODO double clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Pump flow declared | 8.4 gpm · 31.8 L/min | 7.2 gpm · 27.3 L/min | +16% D 6507 (C) |
| Three-point lift, at the coupling points declared | 5,291 lb · 2,400 kg | 4,960 lb · 2,250 kg | +7% D 6507 (C) |
| Rear PTO speeds declared | 540 rpm | 540 rpm / 1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 5,578 lb · 2,530 kg | 6,393 lb · 2,900 kg | +15% 715/5 L (DT) |
| Maximum permissible mass declared | 8,818 lb · 4,000 kg | — | — |
| Wheelbase declared | 83.7 in · 2,125 mm | 86.6 in · 2,200 mm | — |
| Length declared | 148.0 in · 3,760 mm | 149.6 in · 3,800 mm | — |
| Width declared | 81.1 in · 2,060 mm | 70.9–94.5 in · 1,800–2,400 mm | differs |
| Ground clearance declared | 19.3 in · 490 mm | 18.3 in · 465 mm | +5% D 6507 (C) |
| Turning radius, braked declared | 11.7 ft · 3.58 m | 12.5 ft · 3.82 m | +7% 715/5 L (DT) |
| Fuel tank declared | 74.0 qt · 70 L | 88.8 qt · 84.0 L | +20% 715/5 L (DT) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr D 6507 (C) sources
Source
- Source: Traktorenlexikon, “Deutz-Fahr D 6507”
- Source: Traktorenlexikon, “Deutz D 6006”
SOMECA 715/5 L (DT) sources
Source
- Source: Traktorenlexikon, “Someca 715/5 L”