Deutz-Fahr D 6507 (C) or Ford 4830 (A)?
Which should you choose?
The figures split: the Ford 4830 (A) is ahead on hydraulic flow; the Deutz-Fahr D 6507 (C) is ahead on three-point lift.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | D 6507 (C) | 4830 (A) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 41.7 kW (55.9 hp)Traktorenlexikon, “Deutz-Fahr D 6507” | 41.6 kW (55.8 hp)Traktorenlexikon, “Ford 4830” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the D 6507 (C) and the 4830 (A). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the D 6507 (C) and the 4830 (A). |
| Which pumps more oil for implements? | 31.8 L/min (8.4 gpm)Traktorenlexikon, “Deutz-Fahr D 6507” | 35.3 L/min (9.3 gpm)Traktorenlexikon, “Ford 4830” | AheadThe Ford 4830 (A) has 11% more hydraulic flow (3.5 L/min / 0.9 gpm) than the Deutz-Fahr D 6507 (C) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,400 kg (5,291 lb)Traktorenlexikon, “Deutz-Fahr D 6507” | 1,987 kg (4,381 lb)Traktorenlexikon, “Ford 4830” | AheadThe Deutz-Fahr D 6507 (C) has 21% more lift (413 kg / 911 lb) than the Ford 4830 (A) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 2,530 kg (5,578 lb)Traktorenlexikon, “Deutz-Fahr D 6507” | 2,960 kg (6,526 lb)Traktorenlexikon, “Ford 4830” | Ahead (a fact, not an advantage)The Ford 4830 (A) is 17% heavier (430 kg / 948 lb) than the Deutz-Fahr D 6507 (C) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 4,000 kg (8,818 lb)Traktorenlexikon, “Deutz-Fahr D 6507” | — | No figureNo call on maximum permissible mass: no figure on record for the 4830 (A). |
| Which has the wider choice of gears? | 8Traktorenlexikon, “Deutz-Fahr D 6507” | 8 to 16Traktorenlexikon, “Ford 4830” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the D 6507 (C) and the 4830 (A). |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Deutz-Fahr D 6507” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Ford 4830” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Deutz-Fahr D 6507” | 540 rpmTraktorenlexikon, “Ford 4830” | EvenEven on PTO speeds: the same speeds (540 rpm). |
| Which PTO runs independently of the ground drive? | — | independentTraktorenlexikon, “Ford 4830” | No figureNo call on PTO independence: not stated for the D 6507 (C). |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “Deutz-Fahr D 6507” | 2WD / 4WDTraktorenlexikon, “Ford 4830” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1982–1984 | 1990–1992 | Ahead (a fact, not an advantage)The Ford 4830 (A) is newer: production began 8 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Ford 4830 (A) has 11% more hydraulic flow (3.5 L/min / 0.9 gpm) than the Deutz-Fahr D 6507 (C) (both pump flow, as stated by the source).
- The Deutz-Fahr D 6507 (C) has 21% more lift (413 kg / 911 lb) than the Ford 4830 (A) (both lift at the hitch ends, as stated by the source).
- The Ford 4830 (A) is 17% heavier (430 kg / 948 lb) than the Deutz-Fahr D 6507 (C) (both unladen weight, as stated by the source).
- The Ford 4830 (A) is newer: production began 8 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540 rpm).
- Even on drive: every machine is available with four-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources