Deutz-Fahr D 6207 (C) or Landini R 8000 Special (TL-15 N)?
Which should you choose?
On performance, every comparable figure that differs favours the Deutz-Fahr D 6207 (C): hydraulic flow and three-point lift. It is also ahead on forward gears and drive.
- The Deutz-Fahr D 6207 (C) suits loader and hydraulic implement work better on this data: 27% (7.5 L/min / 2.0 gpm) more hydraulic flow and 85% (1,100 kg / 2,425 lb) more three-point lift.
- The Deutz-Fahr D 6207 (C) suits heavy draft work (ploughing, cultivating) better on this data: four-wheel drive.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | D 6207 (C) | R 8000 Special (TL-15 N) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 39.5 kW (53.0 hp)Traktorenlexikon, “Deutz-Fahr D 6207” | 39.9 kW (53.5 hp)Traktorenlexikon, “Landini 8000 Special” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the D 6207 (C) and the R 8000 Special (TL-15 N). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the D 6207 (C) and the R 8000 Special (TL-15 N). |
| Which pumps more oil for implements? | 35.3 L/min (9.3 gpm)Traktorenlexikon, “Deutz-Fahr D 6207” | 27.8 L/min (7.3 gpm)Traktorenlexikon, “Landini 8000 Special” | AheadThe Deutz-Fahr D 6207 (C) has 27% more hydraulic flow (7.5 L/min / 2.0 gpm) than the Landini R 8000 Special (TL-15 N) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,400 kg (5,291 lb)Traktorenlexikon, “Deutz-Fahr D 6207” | 1,300 kg (2,866 lb)Traktorenlexikon, “Landini 8000 Special” | AheadThe Deutz-Fahr D 6207 (C) has 85% more lift (1,100 kg / 2,425 lb) than the Landini R 8000 Special (TL-15 N) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 2,530 kg (5,578 lb)Traktorenlexikon, “Deutz-Fahr D 6207” | 2,540 kg (5,600 lb)Traktorenlexikon, “Landini 8000 Special” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 4,000 kg (8,818 lb)Traktorenlexikon, “Deutz-Fahr D 6207” | — | No figureNo call on maximum permissible mass: no figure on record for the R 8000 Special (TL-15 N). |
| Which has the wider choice of gears? | 8Traktorenlexikon, “Deutz-Fahr D 6207” | 6Traktorenlexikon, “Landini 8000 Special” | AheadThe Deutz-Fahr D 6207 (C) has 33% more forward gears (2 gears) than the Landini R 8000 Special (TL-15 N) (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the D 6207 (C) and the R 8000 Special (TL-15 N). |
| Which is faster on the road? | 25 km/h (15.5 mph) to 30 km/h (18.6 mph)Traktorenlexikon, “Deutz-Fahr D 6207” | 30 km/h (18.6 mph)Traktorenlexikon, “Landini 8000 Special” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Deutz-Fahr D 6207” | 540 rpmTraktorenlexikon, “Landini 8000 Special” | EvenEven on PTO speeds: the same speeds (540 rpm). |
| Which PTO runs independently of the ground drive? | — | — | No figureNo call on PTO independence: not stated for the D 6207 (C) and the R 8000 Special (TL-15 N). |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “Deutz-Fahr D 6207” | 2WDTraktorenlexikon, “Landini 8000 Special” | AheadThe Deutz-Fahr D 6207 (C) is available with four-wheel drive; the Landini R 8000 Special (TL-15 N) is two-wheel drive (as stated by the sources). |
| Which is newer, and what about parts? | 1981–1982 | 1967–1974 | Ahead (a fact, not an advantage)The Deutz-Fahr D 6207 (C) is newer: production began 14 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr D 6207 (C) has 27% more hydraulic flow (7.5 L/min / 2.0 gpm) than the Landini R 8000 Special (TL-15 N) (both pump flow, as stated by the source).
- The Deutz-Fahr D 6207 (C) has 85% more lift (1,100 kg / 2,425 lb) than the Landini R 8000 Special (TL-15 N) (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr D 6207 (C) has 33% more forward gears (2 gears) than the Landini R 8000 Special (TL-15 N) (both forward gears, as stated by the source).
- The Deutz-Fahr D 6207 (C) is available with four-wheel drive; the Landini R 8000 Special (TL-15 N) is two-wheel drive (as stated by the sources).
- The Deutz-Fahr D 6207 (C) is newer: production began 14 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540 rpm).
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources