10 material differences · fewer than 12
Tractor oneDeutz-Fahr D 28071982–1988No measured PTO figureTractor twoSOMECA 300 (TD)1972–1978No measured PTO figure
Which should you choose?
Read our verdict on the D 2807 and the 300 (TD) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | D 2807 | 300 (TD) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 28 hp | 27.6 hp | — |
| Engine declared | KHD F2L 912 | FIAT-IVECO 8025.01.200 or 300 | differs |
| Displacement declared | 1.88 L | 1.73 L | +9% D 2807 |
| Maximum torque declared | 76 lb·ft · 103 N·m | 63 lb·ft · 85 N·m | +21% D 2807 |
| Transmission | |||
| Top speed declared | 15.5 mph · 25 km/h | 15.5 mph · 25 km/h | — |
| Clutch declared | — | Pedal-operated dry FIAT single-disc clutch | — |
| Hydraulics & hitch | |||
| Pump flow declared | 9.2 gpm · 35.0 L/min | 2.5 gpm · 9.3 L/min | +276% D 2807 |
| Pressure declared | 2,538 psi · 175 bar | — | — |
| Rear PTO speeds declared | 540 rpm | 540 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 4,057 lb · 1,840 kg | 2,381 lb · 1,080 kg | +70% D 2807 |
| Maximum permissible mass declared | 6,614 lb · 3,000 kg | — | — |
| Wheelbase declared | 73.4 in · 1,865 mm | 66.9 in · 1,700 mm | +10% D 2807 |
| Length declared | 131.1 in · 3,330 mm | 115.4 in · 2,930 mm | +14% D 2807 |
| Width declared | 61.4 in · 1,560 mm | 57.7–78.3 in · 1,465–1,990 mm | differs |
| Ground clearance declared | 17.3 in · 440 mm | 18.5 in · 470 mm | +7% 300 (TD) |
| Turning radius, braked declared | — | 9.5 ft · 2.90 m | — |
| Fuel tank declared | 74.0 qt · 70 L | 30.6 qt · 29.0 L | +141% D 2807 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz-Fahr D 2807 sources
- Source: Traktorenlexikon, “Deutz-Fahr D 2807”
- Source: Traktorenlexikon, “Deutz D 2506”
SOMECA 300 (TD) sources
- Source: Traktorenlexikon, “Someca 300”
- Source: Traktorenlexikon, “Fiat 300/300 DT”