Deutz-Fahr AgroXtra 4.57 or John Deere 3050 (A)?
Which should you choose?
The figures split: the John Deere 3050 (A) is ahead on hydraulic flow; the Deutz-Fahr AgroXtra 4.57 is ahead on three-point lift and PTO speeds.
- The Deutz-Fahr AgroXtra 4.57 suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 750 rpm.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | AgroXtra 4.57 | 3050 (A) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 62 kW (83 hp)Traktorenlexikon, “Deutz-Fahr AgroXtra 4.57” | 62 kW (83 hp)Traktorenlexikon, “John Deere 3050” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the AgroXtra 4.57 and the 3050 (A). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the AgroXtra 4.57 and the 3050 (A). |
| Which pumps more oil for implements? | 47.3 L/min (12.5 gpm)Traktorenlexikon, “Deutz-Fahr AgroXtra 4.57” | 52.3 L/min (13.8 gpm)Traktorenlexikon, “John Deere 3050” | AheadThe John Deere 3050 (A) has 11% more hydraulic flow (5.0 L/min / 1.3 gpm) than the Deutz-Fahr AgroXtra 4.57 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 5,200 kg (11,464 lb)Traktorenlexikon, “Deutz-Fahr AgroXtra 4.57” | 4,526 kg (9,978 lb)Traktorenlexikon, “John Deere 3050” | AheadThe Deutz-Fahr AgroXtra 4.57 has 15% more lift (674 kg / 1,486 lb) than the John Deere 3050 (A) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 3,780 kg (8,333 lb)Traktorenlexikon, “Deutz-Fahr AgroXtra 4.57” | 3,920 kg (8,642 lb)Traktorenlexikon, “John Deere 3050” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 6,600 kg (14,551 lb)Traktorenlexikon, “Deutz-Fahr AgroXtra 4.57” | 6,700 kg (14,771 lb)Traktorenlexikon, “John Deere 3050” | EvenEven on maximum permissible mass (both maximum permissible mass, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which has the wider choice of gears? | 15 to 18Traktorenlexikon, “Deutz-Fahr AgroXtra 4.57” | 8 to 16Traktorenlexikon, “John Deere 3050” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the AgroXtra 4.57 and the 3050 (A). |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr AgroXtra 4.57” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “John Deere 3050” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000/750 rpmTraktorenlexikon, “Deutz-Fahr AgroXtra 4.57” | 540/1000 rpmTraktorenlexikon, “John Deere 3050” | AheadThe Deutz-Fahr AgroXtra 4.57 offers 750 rpm at the PTO, which the John Deere 3050 (A) does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr AgroXtra 4.57” | independentTraktorenlexikon, “John Deere 3050” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 4WDTraktorenlexikon, “Deutz-Fahr AgroXtra 4.57” | 2WD / 4WDTraktorenlexikon, “John Deere 3050” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1990–1995 | 1986–1993 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The John Deere 3050 (A) has 11% more hydraulic flow (5.0 L/min / 1.3 gpm) than the Deutz-Fahr AgroXtra 4.57 (both pump flow, as stated by the source).
- The Deutz-Fahr AgroXtra 4.57 has 15% more lift (674 kg / 1,486 lb) than the John Deere 3050 (A) (both lift at the hitch ends, as stated by the source).
- The Deutz-Fahr AgroXtra 4.57 offers 750 rpm at the PTO, which the John Deere 3050 (A) does not (as stated by the sources).
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on maximum permissible mass (both maximum permissible mass, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power and a creeper range.
← Every figure for both machines, side by side, with sources