Deutz-Fahr Agroplus 80 or Deutz-Fahr DX 3.75 A?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the Agroplus 80 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the DX 3.75 A has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Deutz-Fahr Agroplus 80 suits loader and hydraulic implement work better on this data: 20% (8.0 L/min / 2.1 gpm) more hydraulic flow.
- The Deutz-Fahr DX 3.75 A suits road haulage better on this data: 11% (500 kg / 1,102 lb) more maximum permissible mass.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | Agroplus 80 | DX 3.75 A | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 56.7 kW (76.0 hp)Traktorenlexikon, “Deutz-Fahr Agroplus 80” | 57.1 kW (76.6 hp)Traktorenlexikon, “Deutz-Fahr DX 3.75 A” | Not comparableNot comparable on power at the PTO shaft: the Agroplus 80 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the DX 3.75 A has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the Agroplus 80 and the DX 3.75 A. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the Agroplus 80 and the DX 3.75 A. |
| Which pumps more oil for implements? | 48.0 L/min (12.7 gpm)Traktorenlexikon, “Deutz-Fahr Agroplus 80” | 40.0 L/min (10.6 gpm)Traktorenlexikon, “Deutz-Fahr DX 3.75 A” | AheadThe Deutz-Fahr Agroplus 80 has 20% more hydraulic flow (8.0 L/min / 2.1 gpm) than the Deutz-Fahr DX 3.75 A (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | — | 3,300 kg (7,275 lb)Traktorenlexikon, “Deutz-Fahr DX 3.75 A” | No figureNo call on three-point lift: no figure on record for the Agroplus 80. |
| Which is heavier, for traction? | 2,750 kg (6,063 lb)Traktorenlexikon, “Deutz-Fahr Agroplus 80” | 3,210 kg (7,077 lb)Traktorenlexikon, “Deutz-Fahr DX 3.75 A” | Ahead (a fact, not an advantage)The Deutz-Fahr DX 3.75 A is 17% heavier (460 kg / 1,014 lb) than the Deutz-Fahr Agroplus 80 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 4,500 kg (9,921 lb)Traktorenlexikon, “Deutz-Fahr Agroplus 80” | 5,000 kg (11,023 lb)Traktorenlexikon, “Deutz-Fahr DX 3.75 A” | AheadThe Deutz-Fahr DX 3.75 A has 11% higher maximum permissible mass (500 kg / 1,102 lb) than the Deutz-Fahr Agroplus 80 (both maximum permissible mass, as stated by the source). |
| Which has the wider choice of gears? | 20Traktorenlexikon, “Deutz-Fahr Agroplus 80” | 16Traktorenlexikon, “Deutz-Fahr DX 3.75 A” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the Agroplus 80 and the DX 3.75 A. |
| Which is faster on the road? | 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr Agroplus 80” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 3.75 A” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540 rpm / 1000 rpmTraktorenlexikon, “Deutz-Fahr Agroplus 80” | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 3.75 A” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Fahr Agroplus 80” | independentTraktorenlexikon, “Deutz-Fahr DX 3.75 A” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 2WD / 4WDTraktorenlexikon, “Deutz-Fahr Agroplus 80” | 4WDTraktorenlexikon, “Deutz-Fahr DX 3.75 A” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 2001–2005 | 1993–1996 | Ahead (a fact, not an advantage)The Deutz-Fahr Agroplus 80 is newer: production began 8 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Deutz-Fahr Agroplus 80 has 20% more hydraulic flow (8.0 L/min / 2.1 gpm) than the Deutz-Fahr DX 3.75 A (both pump flow, as stated by the source).
- The Deutz-Fahr DX 3.75 A is 17% heavier (460 kg / 1,014 lb) than the Deutz-Fahr Agroplus 80 (both unladen weight, as stated by the source).
- The Deutz-Fahr DX 3.75 A has 11% higher maximum permissible mass (500 kg / 1,102 lb) than the Deutz-Fahr Agroplus 80 (both maximum permissible mass, as stated by the source).
- The Deutz-Fahr Agroplus 80 is newer: production began 8 years later. We hold no parts-availability data, so there is no call on parts.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the Agroplus 80 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the DX 3.75 A has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift and a creeper range.
← Every figure for both machines, side by side, with sources