10 material differences · fewer than 12
Tractor oneDeutz (KHD) F4L 514/51956–1966No measured PTO figureTractor twoGüldner G 751965–1969No measured PTO figure
Which should you choose?
We will not advise between these two machines, because the drive differs (2WD; 2WD / 4WD). The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
10 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | F4L 514/5 | G 75 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 63.8 hp | — | — |
| Engine declared | KHD F4L 514 | Güldner 6 L 79 | differs |
| Displacement declared | 5.32 L | 4.71 L | +13% F4L 514/5 |
| Maximum torque declared | 210 lb·ft · 285 N·m | 174 lb·ft · 235 N·m | +21% F4L 514/5 |
| Transmission | |||
| Top speed declared | 18.6 mph · 30.0 km/h | 15.0 mph · 24.1 km/h | +24% F4L 514/5 |
| Clutch declared | — | Pedal-operated dry double clutch | — |
| Hydraulics & hitch | |||
| Pressure declared | — | 2,134 psi · 147 bar | — |
| Rear PTO speeds declared | 588 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 6,669 lb · 3,025 kg | 6,724 lb · 3,050 kg | — |
| Maximum permissible mass declared | 9,921 lb · 4,500 kg | 11,023 lb · 5,000 kg | +11% G 75 |
| Wheelbase declared | 96.1 in · 2,440 mm | 95.1 in · 2,416 mm | — |
| Length declared | 153.5 in · 3,900 mm | 159.4–165.4 in · 4,050–4,200 mm | differs |
| Width declared | 77.2 in · 1,962 mm | 76.6 in · 1,945 mm | — |
| Ground clearance declared | 18.5 in · 470 mm | 15.7 in · 400 mm | +18% F4L 514/5 |
| Turning radius, braked declared | 13.1 ft · 4.00 m | 11.7 ft · 3.58 m | +12% F4L 514/5 |
| Fuel tank declared | 89.8 qt · 85 L | 68.7 qt · 65 L | +31% F4L 514/5 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz (KHD) F4L 514/5 sources
- Source: Traktorenlexikon, “Deutz F4L 514/5”
- Source: Traktorenlexikon, “Fahr D 55 L”
Güldner G 75 sources
- Source: Traktorenlexikon, “Güldner G 75”
- Source: Traktorenlexikon, “Güldner G 75A”