10 material differences · fewer than 12
Tractor oneDeutz (KHD) D 30061968–1978No measured PTO figureTractor twoInternational Harvester D-4301956–1962No measured PTO figure
Which should you choose?
Read our verdict on the D 3006 and the D-430 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 5 fields identical or within 5%, which is not counted as material
| Field | D 3006 | D-430 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 30 hp | 29.6 hp | — |
| Engine declared | KHD F2L 912 | INTERNATIONAL-HARVESTER DD-132 | differs |
| Displacement declared | 1.88 L | 2.18 L | +16% D-430 |
| Maximum torque declared | 75 lb·ft · 101 N·m | 90 lb·ft · 122 N·m | +21% D-430 |
| Transmission | |||
| Top speed declared | 12.4 mph · 20 km/h | 12.4 mph · 20 km/h | — |
| Clutch declared | — | Foot-operated dry single-plate clutch from Fichtel & Sachs | — |
| Hydraulics & hitch | |||
| Pump flow declared | 7.1 gpm · 26.8 L/min | 4.1 gpm · 15.5 L/min | +73% D 3006 |
| Pressure declared | 2,538 psi · 175 bar | — | — |
| Rear PTO speeds declared | 540 rpm | 540 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 3,935 lb · 1,785 kg | 3,660 lb · 1,660 kg | +8% D 3006 |
| Maximum permissible mass declared | 6,614 lb · 3,000 kg | 4,409 lb · 2,000 kg | +50% D 3006 |
| Wheelbase declared | 73.4 in · 1,865 mm | 74.0 in · 1,880 mm | — |
| Length declared | 131.5 in · 3,340 mm | 115.4 in · 2,930 mm | +14% D 3006 |
| Width declared | 63.0 in · 1,600 mm | 64.6 in · 1,640 mm | — |
| Ground clearance declared | 16.1 in · 410 mm | 15.2 in · 385 mm | +6% D 3006 |
| Turning radius, braked declared | 10.3 ft · 3.15 m | 9.2 ft · 2.80 m | +13% D 3006 |
| Fuel tank declared | 74.0 qt · 70 L | 31.7–58.1 qt · 30.0–55.0 L | differs |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz (KHD) D 3006 sources
- Source: Traktorenlexikon, “Deutz D 3006”
- Source: Traktorenlexikon, “Deutz D 2506”
International Harvester D-430 sources
- Source: Traktorenlexikon, “McCormick D-430 Farmall”
- Source: Traktorenlexikon, “McCormick DGD 4”