12 material differences
Tractor oneDeutz (KHD) D 25.21960–1964No measured PTO figureTractor twoFiat 211 R (A)1958–1964No measured PTO figure
Which should you choose?
We will not advise between these two machines, because their unladen weight differs by more than 25% (41%); the drive differs (2WD; Two-wheel or four-wheel drive). The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
12 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | D 25.2 | 211 R (A) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 19.6 hp | 19.7 hp | — |
| Engine declared | KHD F2L 712 | FIAT 614.010 | differs |
| Displacement declared | 1.70 L | 1.14 L | +50% D 25.2 |
| Maximum torque declared | 63 lb·ft · 85 N·m | 49 lb·ft · 66.0 N·m | +29% D 25.2 |
| Transmission | |||
| Top speed declared | 12.4–16.4 mph · 20.0–26.4 km/h | 13.7 mph · 22 km/h | differs |
| Clutch declared | Pedal operated single plate clutch in flywheel | Pedal-operated dry single-plate clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | 4.2 gpm · 16.0 L/min | 2.0 gpm · 7.5 L/min | +113% D 25.2 |
| Pressure declared | 2,134 psi · 147 bar | — | — |
| Rear PTO speeds declared | 540 rpm | 540 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 2,844 lb · 1,290 kg | 2,017 lb · 915 kg | +41% D 25.2 |
| Maximum permissible mass declared | 5,071 lb · 2,300 kg | — | — |
| Wheelbase declared | 74.8 in · 1,900 mm | 66.9 in · 1,699 mm | +12% D 25.2 |
| Length declared | 119.7 in · 3,040 mm | 102.4 in · 2,601 mm | +17% D 25.2 |
| Width declared | 63.0 in · 1,600 mm | 47.4–75.2 in · 1,203–1,911 mm | differs |
| Ground clearance declared | 16.9 in · 430 mm | 17.9 in · 455 mm | +6% 211 R (A) |
| Turning radius, braked declared | 8.7 ft · 2.65 m | 9.0 ft · 2.75 m | — |
| Fuel tank declared | 33.8 qt · 32 L | 41.2 qt · 39.0 L | +22% 211 R (A) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Deutz (KHD) D 25.2 sources
- Source: Traktorenlexikon, “Deutz D 25.2”
- Source: Traktorenlexikon, “Deutz D 25.1”
Fiat 211 R (A) sources
- Source: Traktorenlexikon, “Fiat 211 R/241 R”