DEUTZ-ALLIS 8030 or Hürlimann D-550 Hydrostat?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 8030 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the D-550 Hydrostat has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The DEUTZ-ALLIS 8030 suits loader and hydraulic implement work better on this data: 60% (31.3 L/min / 8.3 gpm) more hydraulic flow.
- The DEUTZ-ALLIS 8030 suits road haulage better on this data: 11% (3.0 km/h / 1.9 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 8030 | D-550 Hydrostat | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 98.5 kW (132.1 hp)Traktorenlexikon, “Deutz-Allis 8030” | 99.2 kW (133.0 hp)Traktorenlexikon, “Hürlimann D 550 Hydrostat” | Not comparableNot comparable on power at the PTO shaft: the 8030 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the D-550 Hydrostat has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 8030 and the D-550 Hydrostat. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 8030 and the D-550 Hydrostat. |
| Which pumps more oil for implements? | 83.3 L/min (22.0 gpm)Traktorenlexikon, “Deutz-Allis 8030” | 52.0 L/min (13.7 gpm)Traktorenlexikon, “Hürlimann D 550 Hydrostat” | AheadThe DEUTZ-ALLIS 8030 has 60% more hydraulic flow (31.3 L/min / 8.3 gpm) than the Hürlimann D-550 Hydrostat (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | — | 2,900 kg (6,393 lb)Traktorenlexikon, “Hürlimann D 550 Hydrostat” | No figureNo call on three-point lift: no figure on record for the 8030. |
| Which is heavier, for traction? | 5,194 kg (11,451 lb)Traktorenlexikon, “Deutz-Allis 8030” | 4,300 kg (9,480 lb)Traktorenlexikon, “Hürlimann D 550 Hydrostat” | Ahead (a fact, not an advantage)The DEUTZ-ALLIS 8030 is 21% heavier (894 kg / 1,971 lb) than the Hürlimann D-550 Hydrostat (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 8030 and the D-550 Hydrostat. |
| Which has the wider choice of gears? | 12 to 20 forwardTraktorenlexikon, “Deutz-Allis 8030” | Stepless (CVT)Traktorenlexikon, “Hürlimann D 550 Hydrostat” | DifferTransmissions differ in kind: the DEUTZ-ALLIS 8030 has 12 to 20 forward gears and the Hürlimann D-550 Hydrostat is stepless (CVT) — not called. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 8030 and the D-550 Hydrostat. |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “Deutz-Allis 8030” | 27 km/h (16.8 mph)Traktorenlexikon, “Hürlimann D 550 Hydrostat” | AheadThe DEUTZ-ALLIS 8030 has 11% more top speed (3.0 km/h / 1.9 mph) than the Hürlimann D-550 Hydrostat (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Deutz-Allis 8030” | 540/1000 rpmTraktorenlexikon, “Hürlimann D 550 Hydrostat” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Deutz-Allis 8030” | — | No figureNo call on PTO independence: not stated for the D-550 Hydrostat. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Allis 8030” | Two-wheel or four-wheel driveTraktorenlexikon, “Hürlimann D 550 Hydrostat” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1985–1988 | 1974 | Ahead (a fact, not an advantage)The DEUTZ-ALLIS 8030 is newer: production began 11 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The DEUTZ-ALLIS 8030 has 60% more hydraulic flow (31.3 L/min / 8.3 gpm) than the Hürlimann D-550 Hydrostat (both pump flow, as stated by the source).
- The DEUTZ-ALLIS 8030 is 21% heavier (894 kg / 1,971 lb) than the Hürlimann D-550 Hydrostat (both unladen weight, as stated by the source).
- The DEUTZ-ALLIS 8030 has 11% more top speed (3.0 km/h / 1.9 mph) than the Hürlimann D-550 Hydrostat (both top speed forward, as stated by the source).
- The DEUTZ-ALLIS 8030 is newer: production began 11 years later. We hold no parts-availability data, so there is no call on parts.
- Transmissions differ in kind: the DEUTZ-ALLIS 8030 has 12 to 20 forward gears and the Hürlimann D-550 Hydrostat is stepless (CVT) — not called.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the 8030 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the D-550 Hydrostat has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources