7 material differences · fewer than 12
Tractor oneDEUTZ-ALLIS 60701985–1988No measured PTO figureTractor twoLandini R-7860 (DT) TL-20 N/M (TL-20 DT/M)1988–2000No measured PTO figure
Which should you choose?
Read our verdict on the 6070 and the R-7860 (DT) TL-20 N/M (TL-20 DT/M) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
7 material differences · 5 fields identical or within 5%, which is not counted as material
| Field | 6070 | R-7860 (DT) TL-20 N/M (TL-20 DT/M) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 70.0 hp | 70.0 hp | — |
| Engine declared | ALLIS-CHALMERS 433 T | Perkins LD 4.236 | differs |
| Displacement declared | 3.29 L | 3.87 L | +18% R-7860 (DT) TL-20 N/M (TL-20 DT/M) |
| Maximum torque declared | — | 195 lb·ft · 264 N·m | — |
| Transmission | |||
| Top speed declared | 15.5 mph · 25 km/h | 18.6 mph · 30 km/h | +20% R-7860 (DT) TL-20 N/M (TL-20 DT/M) |
| Clutch declared | — | Dry and air-cooled OMG double clutch | — |
| Hydraulics & hitch | |||
| Pump flow declared | — | 9.8 gpm · 37.2 L/min | — |
| Pressure declared | — | 2,756 psi · 190 bar | — |
| Rear PTO speeds declared | 540 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 6,100 lb · 2,767 kg | 6,305 lb · 2,860 kg | — |
| Wheelbase declared | 93.0 in · 2,362 mm | 89.8 in · 2,281 mm | — |
| Length declared | 146.5 in · 3,721 mm | 146.1 in · 3,710 mm | — |
| Width declared | 68.5 in · 1,740 mm | 78.3 in · 1,990 mm | +14% R-7860 (DT) TL-20 N/M (TL-20 DT/M) |
| Ground clearance declared | 20.4 in · 518 mm | 20.3 in · 515 mm | — |
| Turning radius, braked declared | 10.4 ft · 3.17 m | 13.0 ft · 3.96 m | +25% R-7860 (DT) TL-20 N/M (TL-20 DT/M) |
| Fuel tank declared | 127.9 qt · 121.0 L | 90.9 qt · 86.0 L | +41% 6070 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
DEUTZ-ALLIS 6070 sources
- Source: Traktorenlexikon, “Deutz-Allis 6070”
- Source: Traktorenlexikon, “Deutz-Allis 6060”
Landini R-7860 (DT) TL-20 N/M (TL-20 DT/M) sources
- Source: Traktorenlexikon, “Landini 7860”
- Source: Traktorenlexikon, “Massey Ferguson MF 373”