10 material differences · fewer than 12
Tractor oneCase-Steyr M 9078 (a)1994–2003No measured PTO figureTractor twoDeutz-Fahr DX 3.75 A1993–1996No measured PTO figure
Which should you choose?
Read our verdict on the M 9078 (a) and the DX 3.75 A → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 5 fields identical or within 5%, which is not counted as material
| Field | M 9078 (a) | DX 3.75 A | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 77.0 hp | 76.6 hp | — |
| Engine declared | Steyr-MWM WD 401.81 | KHD F4L 913 | differs |
| Displacement declared | 4.16 L | 4.09 L | — |
| Maximum torque declared | 218 lb·ft · 295 N·m | 183 lb·ft · 248 N·m | +19% M 9078 (a) |
| Transmission | |||
| Top speed declared | 18.6–24.9 mph · 30–40 km/h | 18.6–24.9 mph · 30–40 km/h | — |
| Clutch declared | Dry Fichtel & Sachs double clutch | Independent dry double clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | — | Open centre | — |
| Pump flow declared | 12.7 gpm · 48.1 L/min | 10.6 gpm · 40.0 L/min | +20% M 9078 (a) |
| Pressure declared | 3,481 psi · 240 bar | 3,481 psi · 240 bar | — |
| Rear PTO speeds declared | 430/540/1000 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 8,267 lb · 3,750 kg | 7,077 lb · 3,210 kg | +17% M 9078 (a) |
| Maximum permissible mass declared | 14,330 lb · 6,500 kg | 11,023 lb · 5,000 kg | +30% M 9078 (a) |
| Wheelbase declared | 95.4 in · 2,424 mm | 88.6 in · 2,250 mm | +8% M 9078 (a) |
| Length declared | 156.7 in · 3,980 mm | 141.7 in · 3,600 mm | +11% M 9078 (a) |
| Width declared | 85.4 in · 2,170 mm | 84.2 in · 2,138 mm | — |
| Ground clearance declared | — | 16.1 in · 408 mm | — |
| Turning radius, braked declared | — | 12.8 ft · 3.90 m | — |
| Fuel tank declared | 105.7 qt · 100.0 L | 91.9 qt · 87 L | +15% M 9078 (a) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Case-Steyr M 9078 (a) sources
- Source: Traktorenlexikon, “Steyr M 9078”
- Source: Traktorenlexikon, “Steyr 9078”
Deutz-Fahr DX 3.75 A sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 3.75 A”
- Source: Traktorenlexikon, “Deutz-Fahr DX 3.90”