11 material differences · fewer than 12
Tractor oneCASE-INTERNATIONAL 4230 (DT)1993–1998No measured PTO figureTractor twoURSUS 6012/60141997–2009No measured PTO figure
Which should you choose?
Read our verdict on the 4230 (DT) and the 6012/6014 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
11 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | 4230 (DT) | 6012/6014 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 80.9 hp | 80.9 hp | — |
| Engine declared | IHC D-268 | URSUS 4390-Turbo | differs |
| Displacement declared | 4.39 L | 3.87 L | +14% 4230 (DT) |
| Maximum torque declared | 213 lb·ft · 289 N·m | 220 lb·ft · 298 N·m | — |
| Transmission | |||
| Top speed declared | 18.6–24.9 mph · 30–40 km/h | 18.6 mph · 30 km/h | differs |
| Clutch declared | Pedal-operated dry single-disc clutch | Pedal operated dry Ursus single disc clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | — | 16.2 gpm · 61.3 L/min | — |
| Pressure declared | 2,698 psi · 186 bar | 3,002–3,481 psi · 207–240 bar | differs |
| Three-point lift, at the coupling points declared | 7,055 lb · 3,200 kg | 8,336 lb · 3,781 kg | +18% 6012/6014 |
| Rear PTO speeds declared | 540 rpm / 1000 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 6,658 lb · 3,020 kg | 7,363 lb · 3,340 kg | +11% 6012/6014 |
| Wheelbase declared | 88.7 in · 2,253 mm | 88.6 in · 2,250 mm | — |
| Length declared | 138.2 in · 3,510 mm | 151.6 in · 3,850 mm | +10% 6012/6014 |
| Width declared | 81.9 in · 2,080 mm | 79.1–107.5 in · 2,010–2,730 mm | differs |
| Ground clearance declared | — | 13.8 in · 350 mm | — |
| Turning radius, braked declared | 12.5 ft · 3.80 m | 12.7 ft · 3.86 m | — |
| Fuel tank declared | 118.3 qt · 112.0 L | 126.8 qt · 120.0 L | +7% 6012/6014 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
CASE-INTERNATIONAL 4230 (DT) sources
- Source: Traktorenlexikon, “Case-IH 4230”
URSUS 6012/6014 sources
- Source: Traktorenlexikon, “Ursus 6012/6014”