9 material differences · fewer than 12
Tractor oneCASE-INTERNATIONAL 4220 (DT)1993–1998No measured PTO figureTractor twoDeutz-Fahr Agrolux 802000–2005No measured PTO figure
Which should you choose?
Read our verdict on the 4220 (DT) and the Agrolux 80 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
9 material differences · 6 fields identical or within 5%, which is not counted as material
| Field | 4220 (DT) | Agrolux 80 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 75.9 hp | 76.0 hp | — |
| Engine declared | IHC D-246 | KHD F4L 913 | differs |
| Displacement declared | 4.04 L | 4.09 L | — |
| Maximum torque declared | 189 lb·ft · 256 N·m | 199 lb·ft · 270 N·m | +5% Agrolux 80 |
| Transmission | |||
| Top speed declared | 21.7 mph · 35 km/h | 18.6–24.9 mph · 30–40 km/h | differs |
| Clutch declared | Pedal-operated dry Rockford single-disc clutch | Mechanically operated, dry Borg & Beck single clutch, type: 330 | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | — | Open centre | — |
| Pump flow declared | 17.2 gpm · 65.0 L/min | 9.5 gpm · 36.0 L/min | +81% 4220 (DT) |
| Pressure declared | 2,698 psi · 186 bar | 2,176 psi · 150 bar | +24% 4220 (DT) |
| Three-point lift, at the coupling points declared | 7,055 lb · 3,200 kg | 6,799 lb · 3,084 kg | — |
| Rear PTO speeds declared | 540 rpm / 1000 rpm | 540 rpm / 1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 6,609 lb · 2,998 kg | 6,195 lb · 2,810 kg | +7% 4220 (DT) |
| Maximum permissible mass declared | — | 11,023 lb · 5,000 kg | — |
| Wheelbase declared | 88.0 in · 2,235 mm | 92.5 in · 2,350 mm | — |
| Length declared | 147.6 in · 3,749 mm | 151.4 in · 3,845 mm | — |
| Width declared | 73.0–92.7 in · 1,854–2,354 mm | 81.1 in · 2,060 mm | differs |
| Ground clearance declared | — | 17.7 in · 450 mm | — |
| Fuel tank declared | 118.3 qt · 112.0 L | 79.3 qt · 75 L | +49% 4220 (DT) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
CASE-INTERNATIONAL 4220 (DT) sources
- Source: Traktorenlexikon, “Case-IH 4220”
Deutz-Fahr Agrolux 80 sources
- Source: Traktorenlexikon, “Deutz-Fahr Agrolux 80”
- Source: Traktorenlexikon, “Deutz-Fahr DX 3.90”