Case-IH Magnum 7210 or Fiat 1580 (DT)?
Which should you choose?
On performance, every comparable figure that differs favours the Case-IH Magnum 7210: hydraulic flow, three-point lift and maximum permissible mass.
- The Case-IH Magnum 7210 suits loader and hydraulic implement work better on this data: 97% (54.2 L/min / 14.3 gpm) more hydraulic flow and 46% (2,266 kg / 4,996 lb) more three-point lift.
- The Case-IH Magnum 7210 suits road haulage better on this data: 13% (1,300 kg / 2,866 lb) more maximum permissible mass.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | Magnum 7210 | 1580 (DT) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 98.4 kW (132.0 hp)Traktorenlexikon, “Case-IH 7210” | 99.4 kW (133.3 hp)Traktorenlexikon, “Fiat 1580 DT” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the Magnum 7210 and the 1580 (DT). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the Magnum 7210 and the 1580 (DT). |
| Which pumps more oil for implements? | 110 L/min (29.1 gpm)Traktorenlexikon, “Case-IH 7210” | 55.8 L/min (14.7 gpm)Traktorenlexikon, “Fiat 1580 DT” | AheadThe Case-IH Magnum 7210 has 97% more hydraulic flow (54.2 L/min / 14.3 gpm) than the Fiat 1580 (DT) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 7,200 kg (15,873 lb)Traktorenlexikon, “Case-IH 7210” | 4,934 kg (10,878 lb)Traktorenlexikon, “Fiat 1580 DT” | AheadThe Case-IH Magnum 7210 has 46% more lift (2,266 kg / 4,996 lb) than the Fiat 1580 (DT) (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 7,525 kg (16,590 lb)Traktorenlexikon, “Case-IH 7210” | 6,500 kg (14,330 lb)Traktorenlexikon, “Fiat 1580 DT” | Ahead (a fact, not an advantage)The Case-IH Magnum 7210 is 16% heavier (1,025 kg / 2,260 lb) than the Fiat 1580 (DT) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 11,300 kg (24,912 lb)Traktorenlexikon, “Case-IH 7210” | 10,000 kg (22,046 lb)Traktorenlexikon, “Fiat 1580 DT” | AheadThe Case-IH Magnum 7210 has 13% higher maximum permissible mass (1,300 kg / 2,866 lb) than the Fiat 1580 (DT) (both maximum permissible mass, as stated by the source). |
| Which has the wider choice of gears? | 24Traktorenlexikon, “Case-IH 7210” | 12 to 24Traktorenlexikon, “Fiat 1580 DT” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | YesTraktorenlexikon, “Case-IH 7210” | — | No figureNo call on a creeper range: not stated for the 1580 (DT). |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Case-IH 7210” | 25 km/h (15.5 mph) to 30 km/h (18.6 mph)Traktorenlexikon, “Fiat 1580 DT” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Case-IH 7210” | 540/1000 rpmTraktorenlexikon, “Fiat 1580 DT” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Case-IH 7210” | independentTraktorenlexikon, “Fiat 1580 DT” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 4WDTraktorenlexikon, “Case-IH 7210” | Two-wheel or four-wheel driveTraktorenlexikon, “Fiat 1580 DT” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1994–1997 | 1979–1984 | Ahead (a fact, not an advantage)The Case-IH Magnum 7210 is newer: production began 15 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Case-IH Magnum 7210 has 97% more hydraulic flow (54.2 L/min / 14.3 gpm) than the Fiat 1580 (DT) (both pump flow, as stated by the source).
- The Case-IH Magnum 7210 has 46% more lift (2,266 kg / 4,996 lb) than the Fiat 1580 (DT) (both lift at the hitch ends, as stated by the source).
- The Case-IH Magnum 7210 is 16% heavier (1,025 kg / 2,260 lb) than the Fiat 1580 (DT) (both unladen weight, as stated by the source).
- The Case-IH Magnum 7210 has 13% higher maximum permissible mass (1,300 kg / 2,866 lb) than the Fiat 1580 (DT) (both maximum permissible mass, as stated by the source).
- The Case-IH Magnum 7210 is newer: production began 15 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power and a creeper range.
← Every figure for both machines, side by side, with sources