Case-IH JX 1060 C or Fiat 60-56 LM (DT)?
Which should you choose?
On performance, every comparable figure that differs favours the Case-IH JX 1060 C: hydraulic flow. It is also ahead on forward gears and PTO speeds.
- The Case-IH JX 1060 C suits PTO-driven implements (mowers, balers, pumps) better on this data: offers 1000 rpm.
- The Case-IH JX 1060 C suits loader and hydraulic implement work better on this data: 59% (19.3 L/min / 5.1 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | JX 1060 C | 60-56 LM (DT) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 35.3 kW (47.3 hp)Traktorenlexikon, “Case-IH JX1060C” | 35.1 kW (47.1 hp)Traktorenlexikon, “Fiatagri 60-56 LM (DT)” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the JX 1060 C and the 60-56 LM (DT). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the JX 1060 C and the 60-56 LM (DT). |
| Which pumps more oil for implements? | 52.1 L/min (13.8 gpm)Traktorenlexikon, “Case-IH JX1060C” | 32.8 L/min (8.7 gpm)Traktorenlexikon, “Fiatagri 60-56 LM (DT)” | AheadThe Case-IH JX 1060 C has 59% more hydraulic flow (19.3 L/min / 5.1 gpm) than the Fiat 60-56 LM (DT) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | — | 1,745 kg (3,847 lb)Traktorenlexikon, “Fiatagri 60-56 LM (DT)” | No figureNo call on three-point lift: no figure on record for the JX 1060 C. |
| Which is heavier, for traction? | 3,165 kg (6,978 lb)Traktorenlexikon, “Case-IH JX1060C” | 2,190 kg (4,828 lb)Traktorenlexikon, “Fiatagri 60-56 LM (DT)” | Ahead (a fact, not an advantage)The Case-IH JX 1060 C is 45% heavier (975 kg / 2,150 lb) than the Fiat 60-56 LM (DT) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 4,800 kg (10,582 lb)Traktorenlexikon, “Case-IH JX1060C” | — | No figureNo call on maximum permissible mass: no figure on record for the 60-56 LM (DT). |
| Which has the wider choice of gears? | 16 to 44Traktorenlexikon, “Case-IH JX1060C” | 8 to 12Traktorenlexikon, “Fiatagri 60-56 LM (DT)” | AheadThe Case-IH JX 1060 C has 33% more forward gears (4 gears) than the Fiat 60-56 LM (DT) (both forward gears, as stated by the source). |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the JX 1060 C and the 60-56 LM (DT). |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Case-IH JX1060C” | 30 km/h (18.6 mph)Traktorenlexikon, “Fiatagri 60-56 LM (DT)” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540E/540/1000E/1000 rpmTraktorenlexikon, “Case-IH JX1060C” | 540 rpmTraktorenlexikon, “Fiatagri 60-56 LM (DT)” | AheadThe Case-IH JX 1060 C offers 1000 rpm at the PTO, which the Fiat 60-56 LM (DT) does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | — | independentTraktorenlexikon, “Fiatagri 60-56 LM (DT)” | No figureNo call on PTO independence: not stated for the JX 1060 C. |
| Which drives on both axles? | 4WD / 2WDTraktorenlexikon, “Case-IH JX1060C”; OECD test report 2156, 2004; OECD test report 2157, 2004 | Two-wheel or four-wheel driveTraktorenlexikon, “Fiatagri 60-56 LM (DT)” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 2003–2008 | 1988– | Ahead (a fact, not an advantage)The Case-IH JX 1060 C is newer: production began 15 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Case-IH JX 1060 C has 59% more hydraulic flow (19.3 L/min / 5.1 gpm) than the Fiat 60-56 LM (DT) (both pump flow, as stated by the source).
- The Case-IH JX 1060 C is 45% heavier (975 kg / 2,150 lb) than the Fiat 60-56 LM (DT) (both unladen weight, as stated by the source).
- The Case-IH JX 1060 C has 33% more forward gears (4 gears) than the Fiat 60-56 LM (DT) (both forward gears, as stated by the source).
- The Case-IH JX 1060 C offers 1000 rpm at the PTO, which the Fiat 60-56 LM (DT) does not (as stated by the sources).
- The Case-IH JX 1060 C is newer: production began 15 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on drive: every machine is available with four-wheel drive.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources