12 material differences
Tractor oneCase-IH CS-75 A1994–2001No measured PTO figureTractor twoVALMET 6000-41993–1996No measured PTO figure
Which should you choose?
Read our verdict on the CS-75 A and the 6000-4 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
12 material differences · 2 fields identical or within 5%, which is not counted as material
| Field | CS-75 A | 6000-4 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 74.0 hp | 74.0 hp | — |
| Engine declared | MWM 301.88 T | VALMET 420 D | differs |
| Displacement declared | — | 4.40 L | — |
| Maximum torque declared | — | 182 lb·ft · 247 N·m | — |
| Transmission | |||
| Top speed declared | 18.6–24.9 mph · 30–40 km/h | 18.6–24.9 mph · 30–40 km/h | — |
| Clutch declared | Dry double clutch | dry single-plate clutch | differs |
| Hydraulics & hitch | |||
| Pump flow declared | 10.9 gpm · 41.4 L/min | 21.2 gpm · 80.3 L/min | +94% 6000-4 |
| Pressure declared | 3,481 psi · 240 bar | 2,901 psi · 200 bar | +20% CS-75 A |
| Rear PTO speeds declared | 540 rpm / 1000 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 6,834 lb · 3,100 kg | 9,193 lb · 4,170 kg | +35% 6000-4 |
| Maximum permissible mass declared | 9,921 lb · 4,500 kg | 14,330 lb · 6,500 kg | +44% 6000-4 |
| Wheelbase declared | 87.8 in · 2,229 mm | 99.6 in · 2,530 mm | +14% 6000-4 |
| Length declared | 149.3 in · 3,792 mm | 175.2 in · 4,450 mm | +17% 6000-4 |
| Width declared | 74.8 in · 1,900 mm | 85.2 in · 2,165 mm | +14% 6000-4 |
| Ground clearance declared | 15.7 in · 400 mm | 16.9 in · 430 mm | +8% 6000-4 |
| Turning radius, braked declared | — | 15.3 ft · 4.65 m | — |
| Fuel tank declared | 87.7 qt · 83.0 L | 167.0 qt · 158.0 L | +90% 6000-4 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Case-IH CS-75 A sources
Source
- Source: Traktorenlexikon, “Case-IH CS75a”
- Source: Traktorenlexikon, “Steyr M 975”
VALMET 6000-4 sources
Source
- Source: Traktorenlexikon, “Valmet 6000”
- Source: Traktorenlexikon, “Valmet 665”