12 material differences
Tractor oneALLIS-CHALMERS 220 Landhandler1969–1973No measured PTO figureTractor twoFiat 140-90 (DT)1984–1993No measured PTO figure
Which should you choose?
Read our verdict on the 220 Landhandler and the 140-90 (DT) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
12 material differences · 2 fields identical or within 5%, which is not counted as material
| Field | 220 Landhandler | 140-90 (DT) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 136.1 hp | 138 hp | — |
| Engine declared | ALLIS-CHALMERS D-3500 | FIAT-IVECO 8065.25.000 | differs |
| Displacement declared | 6.97 L | 5.86 L | +19% 220 Landhandler |
| Maximum torque declared | — | 343 lb·ft · 465 N·m | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6–24.9 mph · 30–40 km/h | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | Open centre | — |
| Pump flow declared | 16.5 gpm · 62.5 L/min | 13.4 gpm · 50.8 L/min | +23% 220 Landhandler |
| Rear PTO speeds declared | 1000 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 12,161 lb · 5,516 kg | 12,809 lb · 5,810 kg | +5% 140-90 (DT) |
| Maximum permissible mass declared | — | 19,842 lb · 9,000 kg | — |
| Wheelbase declared | 100.0 in · 2,539 mm | 108.3 in · 2,750 mm | +8% 140-90 (DT) |
| Length declared | 164.0 in · 4,166 mm | 180.3 in · 4,580 mm | +10% 140-90 (DT) |
| Width declared | 96.0 in · 2,438 mm | 80.7–108.3 in · 2,050–2,750 mm | differs |
| Ground clearance declared | 21.0 in · 533 mm | 26.2 in · 665 mm | +25% 140-90 (DT) |
| Turning radius, braked declared | 11.3 ft · 3.45 m | 12.9 ft · 3.93 m | +14% 140-90 (DT) |
| Fuel tank declared | 203.9 qt · 193.0 L | 190.2 qt · 180.0 L | +7% 220 Landhandler |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
ALLIS-CHALMERS 220 Landhandler sources
- Source: Traktorenlexikon, “Allis-Chalmers 220”
- Source: Traktorenlexikon, “Allis-Chalmers 210”
Fiat 140-90 (DT) sources
- Source: Traktorenlexikon, “Fiatagri 140-90 DT”