AGRIFULL 80-66 (DT) or John Deere 2355 (A)?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 80-66 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 2355 (A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The John Deere 2355 (A) suits loader and hydraulic implement work better on this data: 73% (23.4 L/min / 6.2 gpm) more hydraulic flow.
- The John Deere 2355 (A) suits road haulage better on this data: 20% (5.0 km/h / 3.1 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 80-66 (DT) | 2355 (A) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 50 kW (67 hp)Traktorenlexikon, “Agrifull 80-66” | 49.3 kW (66.1 hp)Traktorenlexikon, “John Deere 2355” | Not comparableNot comparable on power at the PTO shaft: the 80-66 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 2355 (A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 80-66 (DT) and the 2355 (A). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 80-66 (DT) and the 2355 (A). |
| Which pumps more oil for implements? | 32.1 L/min (8.5 gpm)Traktorenlexikon, “Agrifull 80-66” | 55.5 L/min (14.7 gpm)Traktorenlexikon, “John Deere 2355” | AheadThe John Deere 2355 (A) has 73% more hydraulic flow (23.4 L/min / 6.2 gpm) than the AGRIFULL 80-66 (DT) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 2,192 kg (4,833 lb)Traktorenlexikon, “Agrifull 80-66” | — | No figureNo call on three-point lift: no figure on record for the 2355 (A). |
| Which is heavier, for traction? | 2,520 kg (5,556 lb)Traktorenlexikon, “Agrifull 80-66” | 3,075 kg (6,779 lb)Traktorenlexikon, “John Deere 2355” | Ahead (a fact, not an advantage)The John Deere 2355 (A) is 22% heavier (555 kg / 1,224 lb) than the AGRIFULL 80-66 (DT) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the 80-66 (DT) and the 2355 (A). |
| Which has the wider choice of gears? | 12Traktorenlexikon, “Agrifull 80-66” | 8 to 16Traktorenlexikon, “John Deere 2355” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 80-66 (DT) and the 2355 (A). |
| Which is faster on the road? | 25 km/h (15.5 mph)Traktorenlexikon, “Agrifull 80-66” | 30 km/h (18.6 mph)Traktorenlexikon, “John Deere 2355” | AheadThe John Deere 2355 (A) has 20% more top speed (5.0 km/h / 3.1 mph) than the AGRIFULL 80-66 (DT) (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Agrifull 80-66” | 540 rpmTraktorenlexikon, “John Deere 2355” | EvenEven on PTO speeds: the same speeds (540 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Agrifull 80-66” | independentTraktorenlexikon, “John Deere 2355” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “Agrifull 80-66” | 2WD / 4WDTraktorenlexikon, “John Deere 2355” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1980–1986 | 1987–1992 | Ahead (a fact, not an advantage)The John Deere 2355 (A) is newer: production began 7 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The John Deere 2355 (A) has 73% more hydraulic flow (23.4 L/min / 6.2 gpm) than the AGRIFULL 80-66 (DT) (both pump flow, as stated by the source).
- The John Deere 2355 (A) is 22% heavier (555 kg / 1,224 lb) than the AGRIFULL 80-66 (DT) (both unladen weight, as stated by the source).
- The John Deere 2355 (A) has 20% more top speed (5.0 km/h / 3.1 mph) than the AGRIFULL 80-66 (DT) (both top speed forward, as stated by the source).
- The John Deere 2355 (A) is newer: production began 7 years later. We hold no parts-availability data, so there is no call on parts.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the 80-66 (DT) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 2355 (A) has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources