11 material differences · fewer than 12
Tractor oneAgco DT-180 A2005–2008No measured PTO figureTractor twoCase-IH 7230 PRO/89301997–1999No measured PTO figure
Which should you choose?
Read our verdict on the DT-180 A and the 7230 PRO/8930 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
11 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | DT-180 A | 7230 PRO/8930 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 212.0 hp | 211.1 hp | — |
| Engine declared | SISU-DIESEL 74 ETA | CUMMINS 6 TA-830 | differs |
| Displacement declared | 7.37 L | 8.27 L | +12% 7230 PRO/8930 |
| Maximum torque declared | 645 lb·ft · 875 N·m | 614 lb·ft · 833 N·m | — |
| Transmission | |||
| Top speed declared | 24.9–31.1 mph · 40–50 km/h | 18.6–24.9 mph · 30–40 km/h | differs |
| Clutch declared | Electro-hydraulically operated wet multi-disc PTO clutch | — | — |
| Hydraulics & hitch | |||
| Hydraulic control declared | Load sensing | — | — |
| Pump flow declared | 37.4 gpm · 141.5 L/min | 29.7 gpm · 112.4 L/min | +26% DT-180 A |
| Pressure declared | 2,176 psi · 150 bar | 2,451 psi · 169 bar | +13% 7230 PRO/8930 |
| Rear PTO speeds declared | 540/1000/540E rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 19,908 lb · 9,030 kg | 17,864 lb · 8,103 kg | +11% DT-180 A |
| Maximum permissible mass declared | 30,865 lb · 14,000 kg | 25,519 lb · 11,575 kg | +21% DT-180 A |
| Wheelbase declared | 121.1 in · 3,075 mm | 118.3 in · 3,006 mm | — |
| Length declared | 206.3 in · 5,240 mm | 200.1 in · 5,083 mm | — |
| Width declared | 100.4 in · 2,550 mm | 120.0–153.1 in · 3,048–3,890 mm | differs |
| Ground clearance declared | 18.5 in · 470 mm | 17.3 in · 439 mm | +7% DT-180 A |
| Fuel tank declared | 697.4 qt · 660.0 L | 379.4–470.2 qt · 359.0–445.0 L | differs |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Agco DT-180 A sources
- Source: Traktorenlexikon, “AGCO DT 180 A”
Case-IH 7230 PRO/8930 sources
- Source: Traktorenlexikon, “Case-IH 7230 PRO/8930”